Lancia Motor Club Forum Banner
21 June, 2021, 06:07:07 AM *
Welcome, Guest. Please login or register.

Login with username, password and session length
News: Need to contact the Forum Administrator? e-mail forum.admin@lanciamc.co.uk, for Database Administrator e-mail database.admin@lanciamc.co.uk      -      Copy deadline for Viva Lancia is 12th of each month.      -      For Events e-mail events@lanciamc.co.uk      -      To Join the club go to http://www.lanciamc.co.uk/join.htm
 
   Home   Help Search Calendar Register  
Pages: 1 2 3 4 5 [6]   Go Down
  Print  
Author Topic: Dedra turbo H630 XGN  (Read 3696 times)
0 Members and 1 Guest are viewing this topic.
Kevinlincs
Permanent resident
**
Posts: 1058


« Reply #75 on: 09 June, 2021, 09:29:20 PM »

Bit more done, if anyone is still following.
The rear corner near the wiring loom earth had some rust, so that all got cut out but thankfully it only went a few inches along the back panel.
The side panel where the vent sits had been repaired before, both the rusted original and the rusted replacement had to be gone.



* IMG_20210609_153137.jpg (1550.24 KB, 3264x2448 - viewed 3 times.)
Logged
Kevinlincs
Permanent resident
**
Posts: 1058


« Reply #76 on: 09 June, 2021, 09:32:16 PM »

A new panel made for the floor and spot welded to the new vent opening panel.

The rest of the opening and the inner arch that is covered in black underseal I'll chop out next time, it can't be any good under there.


* IMG_20210609_190223.jpg (1725.94 KB, 3264x2448 - viewed 2 times.)

* IMG_20210609_190208.jpg (1523.6 KB, 3264x2448 - viewed 2 times.)
Logged
Kevinlincs
Permanent resident
**
Posts: 1058


« Reply #77 on: 09 June, 2021, 09:34:51 PM »

The outer panel is a bit like Swiss cheese, the inner section much the same.
A bumper mount would be handy too!


* IMG_20210609_190242.jpg (1605.16 KB, 2448x3264 - viewed 2 times.)

* IMG_20210609_190720.jpg (1578.62 KB, 3264x2448 - viewed 2 times.)
Logged
SanRemo78
Rebel Poster
*
Posts: 698



« Reply #78 on: 10 June, 2021, 07:52:23 AM »

Following this one to the bitter end Kevin! Probably Mathewsons? These are the best sort of threads on the forum.

Guy
Logged
lancianut666
Permanent resident
**
Posts: 1353


Slow but rough


« Reply #79 on: 10 June, 2021, 05:40:27 PM »

I think a Dedra Turbo is probably a keeper my sons rate the one I had as the best car Dad ever had.
Logged

Fulvia Coupe S2 Flavia Coupe 1967 1.8 Kugelfischer Prisma 1.6 carb Y10 Fila Y10 Touring Dedra 1.8 Dedra 2.0 Turbo Appia S1
Kevinlincs
Permanent resident
**
Posts: 1058


« Reply #80 on: 10 June, 2021, 09:29:02 PM »

OK, good to know people are following, I'll carry on posting!  Grin
Ideally I'd like to keep this one, I had one years ago and loved it then, in a lot of ways a better car than the integrale as it goes under the radar without drawing attention to itself yet is still very capable.
Whatever though I will endeavor to rid it of all rust so it can now have its future assured.
Logged
SanRemo78
Rebel Poster
*
Posts: 698



« Reply #81 on: 11 June, 2021, 07:34:28 AM »

There's a very nice, low mileage Dedra on eBay at the moment. Started at 7500 but down to 4500. Had it been a turbo instead of the 1.8 I suspect it would have been long gone...
Logged
neil-yaj396
Committee
Permanent resident
*****
Posts: 1083



« Reply #82 on: 11 June, 2021, 08:25:07 AM »

3243 views as of today Kevin, so you definitely have a following, as always...
Logged

1979 1300 Beta Coupe, 2014 Ypsilon 1.2 S Series Momo
frankxhv773t
Permanent resident
**
Posts: 1996



« Reply #83 on: 11 June, 2021, 09:03:29 AM »

I'm a little surprised you aren't taking the back wings off to improve access given you are making such a thorough job of the restoration.
Logged
Kevinlincs
Permanent resident
**
Posts: 1058


« Reply #84 on: 14 June, 2021, 08:25:39 PM »

I wouldn't rule out taking the rear wings off , if only to see how simple that is. I've left them on so far as a reference point, to repair the inner wing section where it meets the outer quarter it will indeed be easier with it all out of the way. Once the lower floor sections are done I will look at it again.

Good to know people are following. Not as quick a pace as the Y10 build was, but then I'm back at work full time so this is just my spare time build now, and I'm in no rush.
Logged
Pages: 1 2 3 4 5 [6]   Go Up
  Print  
 
Jump to:  

Contact the Forum Administrator

LMC Forum copyright © 2007 - 2021 Lancia Motor Club Ltd

Powered by SMF 1.1.20 | SMF © 2006-2011, Simple Machines
Page created in 0.08 seconds with 21 queries.