Lancia Motor Club Forum Banner
28 March, 2024, 07:46:14 PM *
Welcome, Guest. Please login or register.

Login with username, password and session length
News: Need to contact the Forum Administrator? e-mail forum.admin@lanciamc.co.uk, for Database Administrator e-mail database.admin@lanciamc.co.uk      -      Copy deadline for Viva Lancia is 12th of each month.      -      For Events e-mail events@lanciamc.co.uk      -      To Join the club go to http://www.lanciamc.co.uk/join.htm
 
   Home   Help Search Calendar Register  
Pages: 1 2 3 [4] 5 6 7 8 9 ... 17   Go Down
  Print  
Author Topic: E55 LBR the parallel project  (Read 79621 times)
0 Members and 1 Guest are viewing this topic.
frankxhv773t
Permanent resident
**
Posts: 2204



« Reply #45 on: 15 May, 2019, 07:10:21 PM »

Nothing that sophisticated Tim. It's just a flat strip of tin wrapped round the flexi pipe, pinched together at the ends with a hole to bolt it to the strut. I haven't ever seen new ones but it would be simple enough to make.
Logged
frankxhv773t
Permanent resident
**
Posts: 2204



« Reply #46 on: 15 May, 2019, 07:27:54 PM »

Like this.


* Front brake flexi pipe retainer.jpg (81.2 KB, 640x480 - viewed 699 times.)
Logged
fay66
Permanent resident
**
Posts: 6189



« Reply #47 on: 15 May, 2019, 10:26:48 PM »

Like this.
The suggested new clips position can be seen top left holding the pipe to the bracket, with small hole showing.
Brian
8227  Cool
Logged

Own 1966 Fulvia 2C Berlina since 1997, back on road 11-1999.Known as "Fay"
2006 Renault Megane 1 5 Dci Sports Tourer
Dedra Technical Adviser
lancianut666
Permanent resident
**
Posts: 1651


Slow but rough


« Reply #48 on: 16 May, 2019, 10:49:50 AM »

Fay is right it is the top left one... I've found a source on ebay so I'll buy a set of 4. The clip Frank mentions I can't get off as the bolt is seized a bit of heat when I get up there next week should shift it.
Clarkey
Logged

Fulvia Coupe S2 Flavia Coupe 1967 1.8 Kugelfischer Prisma 1.6 carb Y10 Fila Y10 Touring Dedra 1.8 Dedra 2.0 Turbo Appia S1
lancianut666
Permanent resident
**
Posts: 1651


Slow but rough


« Reply #49 on: 16 May, 2019, 10:52:11 AM »

If any one else needs some
https://www.ebay.co.uk/itm/4X-CLASSIC-FIAT-500-126-900-600-BRAKE-PIPE-HOSE-CLIP-LANCIA-ALFA-ROMEO-X1-9/323313220957
Logged

Fulvia Coupe S2 Flavia Coupe 1967 1.8 Kugelfischer Prisma 1.6 carb Y10 Fila Y10 Touring Dedra 1.8 Dedra 2.0 Turbo Appia S1
frankxhv773t
Permanent resident
**
Posts: 2204



« Reply #50 on: 16 May, 2019, 05:53:29 PM »

I tried too post earlier but got booted out. I realised I was thinking of the attachment for the flexi hose itself rather than the journal to the brake pipe and acknowledged that Tim was correct.
Logged
lancianut666
Permanent resident
**
Posts: 1651


Slow but rough


« Reply #51 on: 27 August, 2019, 11:17:48 AM »

Moral use a spanner the right size...the flexipipe clips are off so I managed to get one caliper back on still need the heat on the flexi to metal brake pipe as the union is corroded to the copper pipe and threatening to snap it so  will have to go easy on that one.The new clips work a treat
Clarkey


* 20190824_173151_resized_1.jpg (228.92 KB, 576x1024 - viewed 394 times.)
Logged

Fulvia Coupe S2 Flavia Coupe 1967 1.8 Kugelfischer Prisma 1.6 carb Y10 Fila Y10 Touring Dedra 1.8 Dedra 2.0 Turbo Appia S1
lancianut666
Permanent resident
**
Posts: 1651


Slow but rough


« Reply #52 on: 30 September, 2019, 09:09:01 AM »

Hi all
Managed to get the other caliper on after a bit of heat loosened the flexi to metal pipe union...will try and get the brakes bled this week.
Clarkey
Logged

Fulvia Coupe S2 Flavia Coupe 1967 1.8 Kugelfischer Prisma 1.6 carb Y10 Fila Y10 Touring Dedra 1.8 Dedra 2.0 Turbo Appia S1
lancianut666
Permanent resident
**
Posts: 1651


Slow but rough


« Reply #53 on: 20 December, 2019, 03:57:17 PM »

only a few months later!!! I managed to get all the front hoses and calipers back together and bled the front brakes single handed (Terry is in Vietnam!) using one of those very useful Gunson Eezibleed gadgets. The pedal felt a bit soft but a couple of pumps must of pushed the piston up against the pads and the pedal went firm. Must try and get a run round the block to give them a test. Dunno when...moving house soon but at least I will be only 30 minutes away.
Merry Xmas all
Clarkey
Logged

Fulvia Coupe S2 Flavia Coupe 1967 1.8 Kugelfischer Prisma 1.6 carb Y10 Fila Y10 Touring Dedra 1.8 Dedra 2.0 Turbo Appia S1
DavidLaver
Permanent resident
**
Posts: 4365



« Reply #54 on: 20 December, 2019, 05:17:13 PM »


All progress is progress...  Hope the move goes smoothly.
Logged

David Laver, Lewisham.
lancianut666
Permanent resident
**
Posts: 1651


Slow but rough


« Reply #55 on: 20 January, 2020, 06:56:07 PM »

To make room for the sulking or is it hulking Appia the Y10 had to be put back on it's wheels and put through a 32 point turn to get it out into the corridor of the unit. We then tried to run it up and down the corridor but the combination of sticking rear brakes and not being able to tickover was very frustrating. I took a back wheel off and the drum is very reluctant to turn so it will have to come off. Question is the lumpy/non-existent tickover due to a) petrol gone off or b)a blocked jet?
Clarkey


* 20200118_162336.jpg (854.94 KB, 2048x1152 - viewed 315 times.)
Logged

Fulvia Coupe S2 Flavia Coupe 1967 1.8 Kugelfischer Prisma 1.6 carb Y10 Fila Y10 Touring Dedra 1.8 Dedra 2.0 Turbo Appia S1
DavidLaver
Permanent resident
**
Posts: 4365



« Reply #56 on: 20 January, 2020, 11:40:03 PM »


Do you have an ultrasonic cleaning bath?  Can the carb be a "kitchen table" project rather than in the cold 100 miles from home?
Logged

David Laver, Lewisham.
lancianut666
Permanent resident
**
Posts: 1651


Slow but rough


« Reply #57 on: 21 January, 2020, 07:11:29 PM »

Hi all
The drum has surrendered to a bashing from an aluminium club hammer and revealed the shoes looked to have been replaced but did not have a chamfer on the leading and trailing edges so making the drum a tight fit. After a bit more walloping with the hammer the drum was back on and with the wheel bolts lightly tightened the drum was quite free. So 10 laps of the compound later the brakes were functioning but the other rear drum was getting hot so that will need to come off sometime. Unfortunately 10 laps did not clear the blockage if there is one in the carb so question is can we drain the tank and clear the carb out and with some fresh petrol cure the cutting out after the engine has warmed up and the choke is pushed in.
Hi David
All the tools are now at the unit awaiting our move sometime around the end of the month so I will get a little playabout when the Appia is delivered on Friday.
Clarkey
Logged

Fulvia Coupe S2 Flavia Coupe 1967 1.8 Kugelfischer Prisma 1.6 carb Y10 Fila Y10 Touring Dedra 1.8 Dedra 2.0 Turbo Appia S1
lancianut666
Permanent resident
**
Posts: 1651


Slow but rough


« Reply #58 on: 24 January, 2020, 07:13:42 PM »

Definitely his best side...


* DSCN4582.JPG (437.13 KB, 1600x1200 - viewed 312 times.)
Logged

Fulvia Coupe S2 Flavia Coupe 1967 1.8 Kugelfischer Prisma 1.6 carb Y10 Fila Y10 Touring Dedra 1.8 Dedra 2.0 Turbo Appia S1
lancianut666
Permanent resident
**
Posts: 1651


Slow but rough


« Reply #59 on: 24 January, 2020, 07:21:12 PM »

Just a though has anyone got one of those alloys going spare...on his bad side he has a steel wheel from a Panda!!!
Logged

Fulvia Coupe S2 Flavia Coupe 1967 1.8 Kugelfischer Prisma 1.6 carb Y10 Fila Y10 Touring Dedra 1.8 Dedra 2.0 Turbo Appia S1
Pages: 1 2 3 [4] 5 6 7 8 9 ... 17   Go Up
  Print  
 
Jump to:  

Contact the Forum Administrator

LMC Forum copyright © 2007 - 2021 Lancia Motor Club Ltd

Powered by SMF 1.1.20 | SMF © 2006-2011, Simple Machines
Page created in 0.079 seconds with 21 queries.