Rob
Megaposter
Posts: 295
|
|
« Reply #120 on: 30 August, 2018, 07:59:52 PM » |
|
It was all going so well.... I was trying to push the pistons out of the front brake calipers by removing one of the brake pads & applying pressure to the brake pedal but they didn't want to budge. Finally the pedal started to move which got my hopes up but when I checked, the pistons were still in the same position When I looked towards the rear of the Delta there was a pool of brake fluid, one of the pipes had split . Unfortunately it had been leaking for a little while before it finally split as the paint had lifted on the bottom half of the rear crossmember . So today I removed the rear crossmember & I'll be looking at getting it powder coated also I've ordered some new front brake calipers as the old ones are seized solid! Cheers, Rob
|
|
|
Logged
|
Rob MacFarlane
1988 Delta HF turbo ie 2000 Fiat Coupe 20v 1987 VW T25 Camper
|
|
|
lancialulu
|
|
« Reply #121 on: 30 August, 2018, 09:24:10 PM » |
|
On the bright side you can remove the rear cross member quite easily!
|
|
|
Logged
|
Its not the winning but taking part! or is it taking apart? Lancias: 1955 Aurelia B12 1967 Fulvia 1.3HFR 1972 Fulvia 1600HF 1972 Fulvia Sport 1600 1983 HPE VX 1988 Delta 1.6GTie 1998 Zeta 21. 12v
|
|
|
DavidLaver
Permanent resident
Posts: 4383
|
|
« Reply #122 on: 31 August, 2018, 09:54:49 AM » |
|
Anything else to look at while its apart?
|
|
|
Logged
|
David Laver, Lewisham.
|
|
|
Rob
Megaposter
Posts: 295
|
|
« Reply #123 on: 31 August, 2018, 10:01:52 PM » |
|
Yes it was fairly straight forward to remove the cross member although I had to cut through the brake pipes that go into the brake balance compensator as the compression nuts had rusted solid. I'm going to replace the brake balance compensator as it's looking pretty tired. Also the plastic connecter that fits in-between the transverse links has broken so I'll have to make a new one. As the cross member is off the car I'm going to get it stripped, galvanised & painted .
|
|
« Last Edit: 29 May, 2019, 10:50:21 PM by Rob »
|
Logged
|
Rob MacFarlane
1988 Delta HF turbo ie 2000 Fiat Coupe 20v 1987 VW T25 Camper
|
|
|
fay66
Permanent resident
Posts: 6223
|
|
« Reply #124 on: 31 August, 2018, 10:58:16 PM » |
|
Yes it was fairly straight forward to remove the cross member although I had to cut through the brake pipes that go into the brake balance compensator as the compression nuts had rusted solid. I'm going to replace the brake balance compensator as it's looking pretty tired. Also the plastic connecter that fits in-between the transverse links has broken so I'll have to make a new one. As the cross member is off the car I'm going to get it stripped, galvanised & painted . I'd have hoped Lancia would have used something better than plastic to make that connector from Keep up the good work Rob, will she be ready in time for Castle Coombe?. Brian 8227
|
|
|
Logged
|
Own 1966 Fulvia 2C Berlina since 1997, back on road 11-1999.Known as "Fay" 2006 Renault Megane 1 5 Dci Sports Tourer Dedra Technical Adviser
|
|
|
Rob
Megaposter
Posts: 295
|
|
« Reply #125 on: 01 September, 2018, 06:05:37 PM » |
|
I'm guessing the reason it's plastic is because it's designed to break. Either that or FIAT were keeping the costs down (more likely). It's not looking good for Castle Combe now as the to do list is getting longer again .
|
|
|
Logged
|
Rob MacFarlane
1988 Delta HF turbo ie 2000 Fiat Coupe 20v 1987 VW T25 Camper
|
|
|
ben
Lapsed
Megaposter
Posts: 456
|
|
« Reply #126 on: 09 September, 2018, 10:52:28 AM » |
|
Hi Rob If you have an entry for Castle Combe you could take my 8V along if your car is not ready. Just check that to make it legal your regular insurance covers you for driving other peoples cars---they usually do. Ben
|
|
|
Logged
|
|
|
|
GialloHPEIan
|
|
« Reply #127 on: 09 September, 2018, 12:47:34 PM » |
|
Hi Rob That plastic part would be an ideal candidate for 3D printing I would think. Good to know that you have a back-up vehicle if you don't complete the work ready for the Autumn Classic event, thanks to Bens kind offer. Regards Ian (6610)
|
|
|
Logged
|
1998 Delta HPE 2.0HF Turbo 16v 1968 Land Rover Series IIa Lightweight 2018 Fiat Ducato L2H2 2011 BMW 1 Series 118i M-Sport Convertible
Prev.Lancias: Beta Spyder 2000('80) Delta HF Turbo Martini('88) Prisma 1600('86) Montecarlo('77) Dedra Turbo(
|
|
|
Rob
Megaposter
Posts: 295
|
|
« Reply #128 on: 10 September, 2018, 09:14:43 PM » |
|
Hi Rob If you have an entry for Castle Combe you could take my 8V along if your car is not ready. Just check that to make it legal your regular insurance covers you for driving other peoples cars---they usually do. Ben
That's very kind of you Ben . Unfortunately my insurance wouldn't cover me as your integrale is in a higher category than my Alfa 147 but thanks for the offer. Fellow Bristol member Steve is giving me a lift in his Evo so I'll be going in style . It's times like these that you realise what a great bunch of blokes we have in the Bristol / Frome area, Viva Lancia!
|
|
|
Logged
|
Rob MacFarlane
1988 Delta HF turbo ie 2000 Fiat Coupe 20v 1987 VW T25 Camper
|
|
|
Rob
Megaposter
Posts: 295
|
|
« Reply #129 on: 10 September, 2018, 09:20:57 PM » |
|
Hi Rob That plastic part would be an ideal candidate for 3D printing I would think. Good to know that you have a back-up vehicle if you don't complete the work ready for the Autumn Classic event, thanks to Bens kind offer. Regards Ian (6610) I had a look to see how much Shapeways would charge to 3D print it & to print a one off they wanted £1200 . So I've bought a block of nylon off eBay for £9 & I'll shape my own using a Hacksaw, files & drills. Keeping it old school (& cheap!) Cheers, Rob
|
|
« Last Edit: 10 September, 2018, 09:24:05 PM by Rob »
|
Logged
|
Rob MacFarlane
1988 Delta HF turbo ie 2000 Fiat Coupe 20v 1987 VW T25 Camper
|
|
|
fay66
Permanent resident
Posts: 6223
|
|
« Reply #130 on: 11 September, 2018, 01:43:49 PM » |
|
Hi Rob That plastic part would be an ideal candidate for 3D printing I would think. Good to know that you have a back-up vehicle if you don't complete the work ready for the Autumn Classic event, thanks to Bens kind offer. Regards Ian (6610) I had a look to see how much Shapeways would charge to 3D print it & to print a one off they wanted £1200 . So I've bought a block of nylon off eBay for £9 & I'll shape my own using a Hacksaw, files & drills. Keeping it old school (& cheap!) Cheers, Rob Quite a lot of small Delta parts in the mechanical parts section, including a brake balance arm still quite expensive at £40 but nicely made. and if you're that way inclined the exterior door handle pull with the Delta HF Logo embossed, ready to paint. Brian 8227
|
|
|
Logged
|
Own 1966 Fulvia 2C Berlina since 1997, back on road 11-1999.Known as "Fay" 2006 Renault Megane 1 5 Dci Sports Tourer Dedra Technical Adviser
|
|
|
Rob
Megaposter
Posts: 295
|
|
« Reply #131 on: 12 October, 2018, 03:04:01 PM » |
|
Progress has been pretty slow recently but at least there's been some . The cross member has been stripped & painted & I've bought new front & rear brake calipers & a new brake balance regulator which altogether came to £600 . Christmas has come early for the Delta!
|
|
|
Logged
|
Rob MacFarlane
1988 Delta HF turbo ie 2000 Fiat Coupe 20v 1987 VW T25 Camper
|
|
|
Rob
Megaposter
Posts: 295
|
|
« Reply #132 on: 12 October, 2018, 03:41:41 PM » |
|
Here's the tie rod connector I made from nylon. It took a fair few hours to carve out but I was quite chuffed with it!
|
|
|
Logged
|
Rob MacFarlane
1988 Delta HF turbo ie 2000 Fiat Coupe 20v 1987 VW T25 Camper
|
|
|
Richard Fridd
Permanent resident
Posts: 3483
|
|
« Reply #133 on: 12 October, 2018, 03:46:15 PM » |
|
All looks very nice. How did you carve the nylon and make the holes?
|
|
|
Logged
|
Richard Nevison Fridd Happy Lancia, Happy Life
|
|
|
Rob
Megaposter
Posts: 295
|
|
« Reply #134 on: 12 October, 2018, 03:55:43 PM » |
|
I used a pillar drill for the holes, a bandsaw to cut out the shape & sandpaper to take off the rough edges. Not a 3D printer in sight!
|
|
|
Logged
|
Rob MacFarlane
1988 Delta HF turbo ie 2000 Fiat Coupe 20v 1987 VW T25 Camper
|
|
|
|