13 December, 2024, 12:31:29 AM
Welcome,
Guest
. Please
login
or
register
.
1 Hour
1 Day
1 Week
1 Month
Forever
Login with username, password and session length
News
:
Need to contact the Forum Administrator? e-mail
forum.admin@lanciamc.co.uk
- Copy deadline for Viva Lancia is 12th of each month. - For Events e-mail
events@lanciamc.co.uk
- To Join the club go to
http://www.lanciamc.co.uk/join.htm
Home
Help
Search
Calendar
Register
Lancia Motor Club
>
Model Technical and Interest
>
Beta and Montecarlo
>
Advice needed on Spider seats
Pages: [
1
]
Go Down
« previous
next »
Print
Author
Topic: Advice needed on Spider seats (Read 3360 times)
0 Members and 1 Guest are viewing this topic.
2cojones
Member
Posts: 26
Advice needed on Spider seats
«
on:
15 March, 2016, 01:06:29 AM »
Hi All,
I have recently bought some secondhand Beta Spider seats and have a couple of queries about them (I am reposting this with a pic this time) :
1. Are the rear seat bases on the Spider (2000 F/L model) meant to have one or two locating lugs, or pins - each of mine have just one lug on the bottom of each base, although on one of them it's very weak, barely hanging on, so cannot be used.
2. On the fronts seats how do I replace the front bolt which holds the runner to the actual seat frame - on one of the seats one runner is loose as the bolt has previously been removed and I cannot access it as the runner itself blocks it and there is no access hole at the front of the runner (the rear bolt on the other hand is easily accessible as there is an access hole in the runner). There was advise previously posted stating that the end of the runner had to be removed but I cannot see how this can be done. I have attached a pic which explains things better.
Any help with these queries would be very much appreciated.
Best regards,
Chris
IMAG0813[1].jpg
(1084.78 KB, 2688x1520 - viewed 447 times.)
Logged
frankxhv773t
Permanent resident
Posts: 2245
Re: Advice needed on Spider seats
«
Reply #1 on:
15 March, 2016, 05:41:49 PM »
As to runner access, I seem to recall you have to bend a stop tab out of the way so the upper and lower halves of the runner can be slid apart. Then you can get at the mounting bolts.
Logged
2cojones
Member
Posts: 26
Re: Advice needed on Spider seats
«
Reply #2 on:
21 March, 2016, 12:56:40 AM »
Hi Frank,
Thanks for that, I'll give it a go and let you know if it works (allowing for rust and hardened grease !). Apologies for the delay in acknowledging your reply, I've been working away all week.
Regards, Chris
Logged
Pages: [
1
]
Go Up
Print
« previous
next »
Jump to:
Please select a destination:
-----------------------------
General
-----------------------------
=> About the LMC Forum
=> General Chat
=> Press/Media: Lancias mentioned, seen or wanted!
=> Competition Information
=> Events 2024
=> Events 2025
=> Local Events
=> LMC Legends
=> Links
-----------------------------
Model Technical and Interest
-----------------------------
=> Pre-Lambda
=> Lambda
=> DiLambda
=> Artena and Astura
=> Augusta
=> Aprilia, Ardennes and Ardea
=> Aurelia
=> Appia
=> Flaminia
=> Flavia
=> Fulvia
=> Stratos
=> Beta and Montecarlo
=> Gamma
=> Delta and Prisma
=> Dedra, Thema and Delta (2nd series)
=> Ypsilon, Musa and Y10
=> Kappa
=> Thesis
=> Delta (2008-)
=> Commercial Vehicles
=> Other Lancia Models
-----------------------------
Buy, Sell and Search
-----------------------------
=> Members' cars for sale
=> Lancia vehicles for sale
=> Lancia vehicles required
=> Spares for sale
=> Spares required
-----------------------------
Events Archive
-----------------------------
=> Events 2011
=> Events 2012
=> Events 2013
=> Events 2014
=> Events 2015
=> Events 2016
=> Events 2017
=> Events 2018
=> Events 2019
=> Events 2020
=> Events 2021
=> Events 2022
=> Events 2023
Loading...