Lancia Motor Club Forum Banner
28 March, 2024, 04:56:20 PM *
Welcome, Guest. Please login or register.

Login with username, password and session length
News: Need to contact the Forum Administrator? e-mail forum.admin@lanciamc.co.uk, for Database Administrator e-mail database.admin@lanciamc.co.uk      -      Copy deadline for Viva Lancia is 12th of each month.      -      For Events e-mail events@lanciamc.co.uk      -      To Join the club go to http://www.lanciamc.co.uk/join.htm
 
   Home   Help Search Calendar Register  
Pages: 1 ... 9 10 11 12 13 [14] 15 16 17 18 19 ... 31   Go Down
  Print  
Author Topic: my new integrale  (Read 160064 times)
0 Members and 1 Guest are viewing this topic.
Kevinlincs
Permanent resident
**
Posts: 1531


« Reply #195 on: 30 September, 2018, 10:01:59 PM »

As the replacement panel had been handily removed with more material than I really needed I could make the decision to join it to the bulkhead inside the car behind the dash rather than the windscreen flange itself.
The A pillars I planned to stagger the joins rather than just jut straight through the whole pillar as that's not a very strong way to join it. The outer panel would be cut about half way up, the door section corner kept all original and the inner pillar would be cut a few inches from the bottom.




* CIMG0983.JPG (2228.69 KB, 3072x2304 - viewed 332 times.)
Logged

Flavia 815 coupe
Dedra turbo
Delta integrale
Kevinlincs
Permanent resident
**
Posts: 1531


« Reply #196 on: 30 September, 2018, 10:03:44 PM »

Measure, measure then measure again before cutting a big section of car away at this late stage!


* CIMG0984.JPG (2218.11 KB, 3072x2304 - viewed 316 times.)
Logged

Flavia 815 coupe
Dedra turbo
Delta integrale
Kevinlincs
Permanent resident
**
Posts: 1531


« Reply #197 on: 30 September, 2018, 10:05:46 PM »

Passenger side not too bad, clean up about all that was required..


* CIMG0985.JPG (2236.18 KB, 3072x2304 - viewed 326 times.)
Logged

Flavia 815 coupe
Dedra turbo
Delta integrale
Kevinlincs
Permanent resident
**
Posts: 1531


« Reply #198 on: 30 September, 2018, 10:06:28 PM »

Drivers side not so, but nothing too bad


* CIMG0986.JPG (2236.15 KB, 3072x2304 - viewed 341 times.)
Logged

Flavia 815 coupe
Dedra turbo
Delta integrale
Kevinlincs
Permanent resident
**
Posts: 1531


« Reply #199 on: 30 September, 2018, 10:07:59 PM »

Well worth removing the original panel though, far worse underneath than even appeared on top!


* CIMG0987.JPG (2260.72 KB, 3072x2304 - viewed 338 times.)
Logged

Flavia 815 coupe
Dedra turbo
Delta integrale
Kevinlincs
Permanent resident
**
Posts: 1531


« Reply #200 on: 30 September, 2018, 10:09:37 PM »

Repairs made to the box section underneath then a new top laid on


* CIMG1000.JPG (2257.03 KB, 3072x2304 - viewed 329 times.)
Logged

Flavia 815 coupe
Dedra turbo
Delta integrale
Kevinlincs
Permanent resident
**
Posts: 1531


« Reply #201 on: 30 September, 2018, 10:12:49 PM »

As you can see from this the "new" panel was in very good shape but even it had some rust around the little drain tubes from the 'screen corners

Note too how much has been remove from the donor panel, always best to use as little as you need


* CIMG1006.JPG (2221.45 KB, 3072x2304 - viewed 328 times.)
Logged

Flavia 815 coupe
Dedra turbo
Delta integrale
Kevinlincs
Permanent resident
**
Posts: 1531


« Reply #202 on: 30 September, 2018, 10:15:17 PM »

My own opinion on those drain tubes is they create far more problems than they solve, every car I've now done that has had them has had issues around them, be that the AlfaSuds or anything else.
So I cut the rot out, made up new sections and have welded them over.


* CIMG1017.JPG (2327.24 KB, 3072x2304 - viewed 320 times.)
Logged

Flavia 815 coupe
Dedra turbo
Delta integrale
Kevinlincs
Permanent resident
**
Posts: 1531


« Reply #203 on: 30 September, 2018, 10:16:50 PM »

Using the alignment frame to check things...


* CIMG1009.JPG (2261.22 KB, 3072x2304 - viewed 337 times.)
Logged

Flavia 815 coupe
Dedra turbo
Delta integrale
Kevinlincs
Permanent resident
**
Posts: 1531


« Reply #204 on: 30 September, 2018, 10:18:44 PM »

And using the body panels to check for bonnet and wing alignment...


* CIMG1027.JPG (2141.07 KB, 3072x2304 - viewed 340 times.)
Logged

Flavia 815 coupe
Dedra turbo
Delta integrale
Kevinlincs
Permanent resident
**
Posts: 1531


« Reply #205 on: 30 September, 2018, 10:20:48 PM »

Let the welding begin!


* CIMG1031.JPG (2229.11 KB, 3072x2304 - viewed 341 times.)
Logged

Flavia 815 coupe
Dedra turbo
Delta integrale
Kevinlincs
Permanent resident
**
Posts: 1531


« Reply #206 on: 30 September, 2018, 10:22:46 PM »

Plug welded to the bulkhead and overlapped on the inner A pillar, careful not to leave sharp edges for the sunroof drain tubes!


* CIMG1037.JPG (2216.36 KB, 3072x2304 - viewed 307 times.)
Logged

Flavia 815 coupe
Dedra turbo
Delta integrale
Kevinlincs
Permanent resident
**
Posts: 1531


« Reply #207 on: 30 September, 2018, 10:24:39 PM »

Repairs to the drivers side bulkhead..


* CIMG1043.JPG (2259.39 KB, 3072x2304 - viewed 280 times.)
Logged

Flavia 815 coupe
Dedra turbo
Delta integrale
Kevinlincs
Permanent resident
**
Posts: 1531


« Reply #208 on: 30 September, 2018, 10:26:49 PM »

Grinding off takes an age  Sad


* CIMG1045.JPG (2217.14 KB, 3072x2304 - viewed 279 times.)
Logged

Flavia 815 coupe
Dedra turbo
Delta integrale
Kevinlincs
Permanent resident
**
Posts: 1531


« Reply #209 on: 30 September, 2018, 10:28:31 PM »

Worth the effort though, outer pillar joint came out well both sides.


* CIMG1046.JPG (872.78 KB, 2304x3072 - viewed 285 times.)
Logged

Flavia 815 coupe
Dedra turbo
Delta integrale
Pages: 1 ... 9 10 11 12 13 [14] 15 16 17 18 19 ... 31   Go Up
  Print  
 
Jump to:  

Contact the Forum Administrator

LMC Forum copyright © 2007 - 2021 Lancia Motor Club Ltd

Powered by SMF 1.1.20 | SMF © 2006-2011, Simple Machines
Page created in 0.119 seconds with 21 queries.