Lancia Motor Club Forum Banner
05 December, 2024, 09:50:08 PM *
Welcome, Guest. Please login or register.

Login with username, password and session length
News: Need to contact the Forum Administrator? e-mail forum.admin@lanciamc.co.uk     -      Copy deadline for Viva Lancia is 12th of each month.      -      For Events e-mail events@lanciamc.co.uk      -      To Join the club go to http://www.lanciamc.co.uk/join.htm
 
   Home   Help Search Calendar Register  
Pages: 1 2 3 4 5 6 [7] 8 9 10 11 12 ... 31   Go Down
  Print  
Author Topic: my new integrale  (Read 190208 times)
0 Members and 1 Guest are viewing this topic.
Kevinlincs
Permanent resident
**
Posts: 1616


« Reply #90 on: 13 February, 2018, 09:54:07 PM »

Another piece was on the opposite side chassis rail, where the gearbox mount plate goes.
Some surface rust which got chopped out and repaired..


* IMG_20170830_165106 (1).jpg (1776.44 KB, 2592x1944 - viewed 426 times.)

* IMG_20170830_183124 (1).jpg (2019.84 KB, 2592x1944 - viewed 444 times.)
Logged

Flavia 815 coupe
Delta integrale
Kevinlincs
Permanent resident
**
Posts: 1616


« Reply #91 on: 13 February, 2018, 09:56:29 PM »

Usual process, make a repair section and weld in..


* IMG_20170830_183340.jpg (1839.89 KB, 2592x1944 - viewed 463 times.)

* IMG_20170830_192852.jpg (1928.33 KB, 2592x1944 - viewed 454 times.)
Logged

Flavia 815 coupe
Delta integrale
DavidLaver
Permanent resident
**
Posts: 4387



« Reply #92 on: 14 February, 2018, 11:21:37 AM »


Bits like the "chassis rail top meets the bulkhead and inner wing/strut area" are really satisfying the way they disappear.  Got the radius bang on.  Can see that "it might be ok" is NOT as assumption to make from all the places you've "been curious" and peeled back to have a look see.

Are you putting any extra structure in?  (noticed the extra plate on the RHD conversion) I think it was "Thurbs" race car build thread that listed a few mods.
Logged

David Laver, Lewisham.
DavidLaver
Permanent resident
**
Posts: 4387



« Reply #93 on: 14 February, 2018, 11:34:40 AM »

Looked back and nothing definitive...but maybe it would pop out the pictures to someone more familiar with them:

https://www.facebook.com/pg/LanciaDeltaRacing/photos/?tab=albums

http://www.lancia.myzen.co.uk/forum/index.php?topic=9531.0

http://www.jjperformance.co.uk/
« Last Edit: 14 February, 2018, 11:37:35 AM by DavidLaver » Logged

David Laver, Lewisham.
Kevinlincs
Permanent resident
**
Posts: 1616


« Reply #94 on: 14 February, 2018, 06:53:22 PM »

I'll have a look through that thanks David, always happy to follow advice from other builds.
I am planning on making extra strengthening sections for bits like the strut tops, I'll do that once I can get the car on the tilter soon.

A few more interesting bits to come on here yet though.
Logged

Flavia 815 coupe
Delta integrale
frankxhv773t
Permanent resident
**
Posts: 2242



« Reply #95 on: 14 February, 2018, 09:06:36 PM »

This is a picture of what I think Abarth added to the works cars.


* schema-abarth Intgrale strengthening plates.jpg (118.45 KB, 625x469 - viewed 621 times.)
Logged
Kevinlincs
Permanent resident
**
Posts: 1616


« Reply #96 on: 14 February, 2018, 10:03:11 PM »

Think I've seen those kits available somewhere, could have been Walkers?
Think it was about £1500 though!
I'll probably have a good look at them then make my own  Wink
Logged

Flavia 815 coupe
Delta integrale
DavidLaver
Permanent resident
**
Posts: 4387



« Reply #97 on: 14 February, 2018, 11:40:04 PM »


Interesting that its more at the front than the back - any of that holding the engine in or all for suspension loads?   

Looking at it the pillars seem obvious places to double up, but only AFTER looking at it.
Logged

David Laver, Lewisham.
frankxhv773t
Permanent resident
**
Posts: 2242



« Reply #98 on: 15 February, 2018, 07:50:28 PM »

I suspect the amount of strengthening at the front is because that hits first on both take off and landing. If the back hits first your rally is probably over anyway!
Logged
Kevinlincs
Permanent resident
**
Posts: 1616


« Reply #99 on: 28 March, 2018, 06:27:45 PM »

I'll post a few more pictures again, seeing as it's been a while since I bombarded you all!

The drivers side rear arch had corrosion mainly inside the car!



* CIMG0005.JPG (2237.09 KB, 3072x2304 - viewed 385 times.)
Logged

Flavia 815 coupe
Delta integrale
Kevinlincs
Permanent resident
**
Posts: 1616


« Reply #100 on: 28 March, 2018, 06:28:43 PM »

A bit of chopping and solid metal was found...


* CIMG0192.JPG (2126.26 KB, 3072x2304 - viewed 414 times.)
Logged

Flavia 815 coupe
Delta integrale
Kevinlincs
Permanent resident
**
Posts: 1616


« Reply #101 on: 28 March, 2018, 06:32:13 PM »

A few plates needed as there was some degree of curvature in several directions plus a strengthening seam for the underside, as it picks up the seat belt mount strength of repair was important.


* CIMG0204.JPG (2218.63 KB, 3072x2304 - viewed 423 times.)
Logged

Flavia 815 coupe
Delta integrale
Kevinlincs
Permanent resident
**
Posts: 1616


« Reply #102 on: 28 March, 2018, 06:34:11 PM »

The bottom outer corner where it meets the sill had some grot to remove..


* CIMG0215.JPG (2212.39 KB, 3072x2304 - viewed 457 times.)
Logged

Flavia 815 coupe
Delta integrale
Kevinlincs
Permanent resident
**
Posts: 1616


« Reply #103 on: 28 March, 2018, 06:35:20 PM »

Starting to gain shape..


* CIMG0220.JPG (2245.84 KB, 3072x2304 - viewed 399 times.)
Logged

Flavia 815 coupe
Delta integrale
Kevinlincs
Permanent resident
**
Posts: 1616


« Reply #104 on: 28 March, 2018, 06:37:02 PM »

The outer lip was deemed unfit so I made a new one, here ready for fitting after shaping to suit the arch and importantly fitting inside the door shut!


* CIMG0224.JPG (2225.04 KB, 3072x2304 - viewed 438 times.)
Logged

Flavia 815 coupe
Delta integrale
Pages: 1 2 3 4 5 6 [7] 8 9 10 11 12 ... 31   Go Up
  Print  
 
Jump to:  

Contact the Forum Administrator

LMC Forum copyright © 2007 - 2021 Lancia Motor Club Ltd

Powered by SMF 1.1.20 | SMF © 2006-2011, Simple Machines
Page created in 0.053 seconds with 21 queries.