Lancia Motor Club Forum Banner
28 March, 2024, 11:38:18 PM *
Welcome, Guest. Please login or register.

Login with username, password and session length
News: Need to contact the Forum Administrator? e-mail forum.admin@lanciamc.co.uk, for Database Administrator e-mail database.admin@lanciamc.co.uk      -      Copy deadline for Viva Lancia is 12th of each month.      -      For Events e-mail events@lanciamc.co.uk      -      To Join the club go to http://www.lanciamc.co.uk/join.htm
 
   Home   Help Search Calendar Register  
Pages: 1 2 [3]   Go Down
  Print  
Author Topic: Progress report  (Read 19407 times)
0 Members and 1 Guest are viewing this topic.
fay66
Permanent resident
**
Posts: 6189



« Reply #30 on: 07 May, 2015, 07:27:00 PM »

Lifted from the 'CUC 20H Fanalone thread:

"Jonathan has stripped and rebuilt the 48 Dellortos using comprehensive overhaul kits, checked the pump filter, overhauled the Filter King fitting new gaskets and spring, fitted a new set of points and she's running better than ever.  Smiley Another case of not knowing which was at fault or maybe it was a mix of all.

He also machine tapered the two faces of the inlet manifold which has lowered the carbs, had the radiator re-cored reducing the height by 20mm and lowered the height of the water manifold and the temperature sender. All of  which has resulted in the bonnet shutting level with the wing tops without fouling the carbs and radiator.  Smiley"

Robin.

Herewith a couple of photos of the carbs (48 Dellorto) on the Fanalone after Jonathan's modifications. The radiator is pulled as far forward as possible by the top rubber mount otherwise the large alternator which is fitted would foul the rad core. We've fitted a metal plate to the core to make absolutely certain that the alternator dosen't ever hole it!

Robin

Robin,

where's the cooling fan?

Brian
8227 Cool
Logged

Own 1966 Fulvia 2C Berlina since 1997, back on road 11-1999.Known as "Fay"
2006 Renault Megane 1 5 Dci Sports Tourer
Dedra Technical Adviser
Neil
Permanent resident
**
Posts: 1281



« Reply #31 on: 07 May, 2015, 09:16:50 PM »

Brian, I think it is on the front of the radiator when I looked at Brooklands.
Logged

Neil   
386

1973 Fulvia S2 1.3
fay66
Permanent resident
**
Posts: 6189



« Reply #32 on: 07 May, 2015, 11:11:04 PM »

Brian, I think it is on the front of the radiator when I looked at Brooklands.

Thanks Neil,
didn't think of that Roll Eyes

Brian
8227 Cool
Logged

Own 1966 Fulvia 2C Berlina since 1997, back on road 11-1999.Known as "Fay"
2006 Renault Megane 1 5 Dci Sports Tourer
Dedra Technical Adviser
Dilambdaman
Permanent resident
**
Posts: 1377



« Reply #33 on: 08 May, 2015, 10:58:36 AM »

Yes, that's right Neil, the fan had to go in front of the rad and blow instead of suck!  The size of the alternator leaves no room for a fan.

Robin.
Logged

Robin Lacey 3222

1932 Dilambda
1992 Y10 GTie
2012 Delta Mk3
lancialulu
Press Officer
Permanent resident
*****
Posts: 4902



« Reply #34 on: 22 May, 2015, 06:22:43 PM »

Fitted one of these bad boys (the lower one) to my 1600 Sport. 19mm stiff FARB. Twice as stiff as the standard 16mm bar.

I know how it will handle as I have one on my HF.....Just waited a long time before asking for another batch to be made.....


* ffatarb.jpg (111.63 KB, 960x540 - viewed 308 times.)
Logged

Its not the winning but taking part! or is it taking apart?
Lancias:
1955 Aurelia B12
1967 Fulvia 1.3HFR
1972 Fulvia 1600HF
1972 Fulvia Sport 1600
1983 HPE VX
1988 Delta 1.6GTie
1998 Zeta 21.  12v
RobD
Lapsed
Senior Member
*****
Posts: 180



« Reply #35 on: 29 May, 2015, 08:00:22 AM »

Just for interest here's a pic of the manifold with its freshly applied ceramic coating . It's been coated inside and out which should hopefully keep rust at bay for many years. The other advantage is reduced heat within the engine compartment.

Logged

You're all entitled to my opinion.
'75 Fulvia 1.3S
'68 works Laverda 125cc ISDT
KTM 640 Adventure
Yamaha TDM 900
Numerous Gas Gas trail bikes...
www.adventureride.co.uk
simonandjuliet
Permanent resident
**
Posts: 2538



« Reply #36 on: 29 May, 2015, 03:00:46 PM »

Very nice !
The ceramic coating, it's a DIY job or specialist ?
Logged

AmilcarCGS, ApriliaCabrio,S2Aprilia,Ardea c'cino,S4 Ardea, Appia c'cino, Appia f'cino,B20 s4,4 R4 Sinpar, R4 Rodeo, 65 Moke, 2xR60 Tractor, 2xToselli 78, Moto Guzzi Ercole, Disco 3, Mini ALL4 JCW, Moto Guzzi Cardellino, Fulvia GT, RE Himalayan, Ypsilon
RobD
Lapsed
Senior Member
*****
Posts: 180



« Reply #37 on: 30 May, 2015, 05:08:11 PM »

Hi Simon,
The coating was done by these folks... http://www.camcoat.com/main/ their website tells you all about the process.
Bob
Logged

You're all entitled to my opinion.
'75 Fulvia 1.3S
'68 works Laverda 125cc ISDT
KTM 640 Adventure
Yamaha TDM 900
Numerous Gas Gas trail bikes...
www.adventureride.co.uk
lancialulu
Press Officer
Permanent resident
*****
Posts: 4902



« Reply #38 on: 23 June, 2015, 07:08:57 AM »

Fitted one of these bad boys (the lower one) to my 1600 Sport. 19mm stiff FARB. Twice as stiff as the standard 16mm bar.

I know how it will handle as I have one on my HF.....Just waited a long time before asking for another batch to be made.....

Just returned from 2000 mile round trip and can say this anti-roll bar upgrade is well worth it. No negatives, just positives on the handling front.
Logged

Its not the winning but taking part! or is it taking apart?
Lancias:
1955 Aurelia B12
1967 Fulvia 1.3HFR
1972 Fulvia 1600HF
1972 Fulvia Sport 1600
1983 HPE VX
1988 Delta 1.6GTie
1998 Zeta 21.  12v
RobD
Lapsed
Senior Member
*****
Posts: 180



« Reply #39 on: 23 June, 2015, 05:20:00 PM »

That's good to hear Tim, will one fit in the Fulvia cabin? If so I will collect the one I've ordered from Omicron when we visit this weekend..,
My GP4 inlet manifold arrived today, very tasty...
Logged

You're all entitled to my opinion.
'75 Fulvia 1.3S
'68 works Laverda 125cc ISDT
KTM 640 Adventure
Yamaha TDM 900
Numerous Gas Gas trail bikes...
www.adventureride.co.uk
lancialulu
Press Officer
Permanent resident
*****
Posts: 4902



« Reply #40 on: 23 June, 2015, 05:38:57 PM »

That's good to hear Tim, will one fit in the Fulvia cabin? If so I will collect the one I've ordered from Omicron when we visit this weekend..,
My GP4 inlet manifold arrived today, very tasty...
It will go in the cabin maybe even the boot...
Logged

Its not the winning but taking part! or is it taking apart?
Lancias:
1955 Aurelia B12
1967 Fulvia 1.3HFR
1972 Fulvia 1600HF
1972 Fulvia Sport 1600
1983 HPE VX
1988 Delta 1.6GTie
1998 Zeta 21.  12v
Pages: 1 2 [3]   Go Up
  Print  
 
Jump to:  

Contact the Forum Administrator

LMC Forum copyright © 2007 - 2021 Lancia Motor Club Ltd

Powered by SMF 1.1.20 | SMF © 2006-2011, Simple Machines
Page created in 0.066 seconds with 21 queries.