Lancia Motor Club Forum Banner
28 March, 2024, 08:25:18 PM *
Welcome, Guest. Please login or register.

Login with username, password and session length
News: Need to contact the Forum Administrator? e-mail forum.admin@lanciamc.co.uk, for Database Administrator e-mail database.admin@lanciamc.co.uk      -      Copy deadline for Viva Lancia is 12th of each month.      -      For Events e-mail events@lanciamc.co.uk      -      To Join the club go to http://www.lanciamc.co.uk/join.htm
 
   Home   Help Search Calendar Register  
Pages: [1]   Go Down
  Print  
Author Topic: Cleaning petrol tank interior?  (Read 7294 times)
0 Members and 1 Guest are viewing this topic.
BlueSky
Lapsed
Senior Member
*****
Posts: 183



WWW
« on: 05 June, 2014, 06:31:59 AM »

The “Slosh” liner in the Aprilia’s petrol tank has been peeling off for sometime so needed to be cleaned out. I had a local radiator man tackle the soldered seam so I could get it in half and  used paint stripper to get the old sealant off and now have the finish you can see in the photo.

Next step is to remove the surface rust from the interior. My question is what is the best method to do this so as not to damage the steel?

Thanks,

Noel


* petrol tank-066.jpg (270.07 KB, 1024x768 - viewed 411 times.)

* petrol tank-093.jpg (256.46 KB, 1024x768 - viewed 392 times.)
Logged

1937 1st series Aprilia Berlina
Nissan X-Trail T31 TS
1920 P & M 3 1/2hp {FOR SALE}
John Deere LX188
www.narrywoolan.com.au/home
the.cern
Permanent resident
**
Posts: 1494


« Reply #1 on: 05 June, 2014, 07:20:19 AM »

Noel, to clean rust from large plain surfaces I use polyester stripping discs, 115mm dia in an angle grinder. That has a minimal effect on the steel, but is very efficient and quick. For small, difficult areas I use a mule skinner, again in an angle grinder (although some have a rev limit of 5000). Jim made up a couple of extra long shanks, about 120mm, which improve accessibility significantly. (http://www.qpaints.co.uk/mule-skin-brush.html). I am sure you can get them down under, but that gives a little more info. about them.

I hope that is of use,

                           Andy
Logged
simonandjuliet
Permanent resident
**
Posts: 2538



« Reply #2 on: 05 June, 2014, 08:53:47 AM »

I use the stripping discs as well on the air grinder, very effective - hard on rust , soft on metal

Re the Slosh - how long had it been in place ? I haven't had a problem with it coming off in the past, but I know others have (and now you) ! What is the percentage of ethanol in your petrol ? They are sneaking in the 10% here in France

Interesting to see the inside of the tank ....
Logged

AmilcarCGS, ApriliaCabrio,S2Aprilia,Ardea c'cino,S4 Ardea, Appia c'cino, Appia f'cino,B20 s4,4 R4 Sinpar, R4 Rodeo, 65 Moke, 2xR60 Tractor, 2xToselli 78, Moto Guzzi Ercole, Disco 3, Mini ALL4 JCW, Moto Guzzi Cardellino, Fulvia GT, RE Himalayan, Ypsilon
the.cern
Permanent resident
**
Posts: 1494


« Reply #3 on: 05 June, 2014, 08:58:27 PM »

Here are a couple of photographs of my mule skinner and the long shank turned up by Jim. This mule skinner is near the end of its useful life. New they are normally 50mm or 63mm diameter.

Good luck whatever you use.

                                        Andy


* photo (57).JPG (374.7 KB, 1296x968 - viewed 407 times.)

* photo (58).JPG (344.2 KB, 1296x968 - viewed 451 times.)
Logged
BlueSky
Lapsed
Senior Member
*****
Posts: 183



WWW
« Reply #4 on: 05 June, 2014, 09:34:19 PM »

Thanks Andy and Simon I think I know what to look for. The Slosh was done way back in August 1991. However I don't think they did it very well as there were some very thick patches and mostly it only got to the bottom of the tank.
We can avoid ethanol petrol here in Victoria as it comes from a different pump, I've only used regular unleaded in the seven years I've had the car, of course I don't know what could have been used when the car was in Europe.
One other thing if you do need to open a tank up as well as the soldered seem is to to remove the six screws that attach the baffles to the top. Yes it is interesting to see inside, also found the tank has had a decent ding that has been filled on the outside! Will keep you informed on my progress.
Noel
Logged

1937 1st series Aprilia Berlina
Nissan X-Trail T31 TS
1920 P & M 3 1/2hp {FOR SALE}
John Deere LX188
www.narrywoolan.com.au/home
BlueSky
Lapsed
Senior Member
*****
Posts: 183



WWW
« Reply #5 on: 12 June, 2014, 03:43:24 AM »

Have made some progress and got most of the metal clean, the nylon brushes did a good job, the wire brush on the angle grinder did the tougher bits. Next I need to get some panel beating done, not my thing, and then have a final clean. Might have to invest in a mini angle die grinder to get into the really tight sections, although I am going to reline it. Found a FIRA makers stamp, whoever that was.
Noel


* petrol tank-098.jpg (196.73 KB, 1024x768 - viewed 407 times.)

* petrol tank-101.jpg (274.43 KB, 1024x768 - viewed 393 times.)

* petrol tank-108.jpg (222.72 KB, 1024x768 - viewed 410 times.)

* petrol tank-119.jpg (312.37 KB, 1024x768 - viewed 405 times.)
Logged

1937 1st series Aprilia Berlina
Nissan X-Trail T31 TS
1920 P & M 3 1/2hp {FOR SALE}
John Deere LX188
www.narrywoolan.com.au/home
Parisien
Administrator
Permanent resident
*****
Posts: 4244



« Reply #6 on: 12 June, 2014, 05:23:39 AM »

Even a Lancia petrol tank is a work of art..........looking much better and hopefully problem fully solved when work completed.


P
Logged

Frank Gallagher
simonandjuliet
Permanent resident
**
Posts: 2538



« Reply #7 on: 12 June, 2014, 05:38:38 AM »

Lovely, must have taken hours !
Logged

AmilcarCGS, ApriliaCabrio,S2Aprilia,Ardea c'cino,S4 Ardea, Appia c'cino, Appia f'cino,B20 s4,4 R4 Sinpar, R4 Rodeo, 65 Moke, 2xR60 Tractor, 2xToselli 78, Moto Guzzi Ercole, Disco 3, Mini ALL4 JCW, Moto Guzzi Cardellino, Fulvia GT, RE Himalayan, Ypsilon
DavidLaver
Permanent resident
**
Posts: 4365



« Reply #8 on: 12 June, 2014, 08:20:03 AM »


Did that extension work ok?  Was there a technique with it such as having the brush wedged into a corner before starting?  Is the chuck separate than the extension?

An idea for the last little corners is a bit of sandpaper and a finger - preferably someone else's!!   

David
Logged

David Laver, Lewisham.
BlueSky
Lapsed
Senior Member
*****
Posts: 183



WWW
« Reply #9 on: 12 June, 2014, 10:02:35 PM »

Yes did take sometime! I'm sure those that do this for a profession must have a quicker method. For the drill extension I used the chuck off my old hand drill screwed onto the hex rod, it helped getting into the centre section and around the baffles. David you're right, some more hand sanding and a bit of work with the Dremel it should be done.
Noel
Logged

1937 1st series Aprilia Berlina
Nissan X-Trail T31 TS
1920 P & M 3 1/2hp {FOR SALE}
John Deere LX188
www.narrywoolan.com.au/home
BlueSky
Lapsed
Senior Member
*****
Posts: 183



WWW
« Reply #10 on: 23 January, 2015, 09:29:55 PM »

Forgot to post the end result, have put it on my blog

https://lanciaapriliadiary.wordpress.com/2014/07/25/petrol-tank-clean-and-repair/

Noel
Logged

1937 1st series Aprilia Berlina
Nissan X-Trail T31 TS
1920 P & M 3 1/2hp {FOR SALE}
John Deere LX188
www.narrywoolan.com.au/home
Pages: [1]   Go Up
  Print  
 
Jump to:  

Contact the Forum Administrator

LMC Forum copyright © 2007 - 2021 Lancia Motor Club Ltd

Powered by SMF 1.1.20 | SMF © 2006-2011, Simple Machines
Page created in 0.075 seconds with 21 queries.