Lancia Motor Club Forum Banner
03 December, 2024, 09:16:38 PM *
Welcome, Guest. Please login or register.

Login with username, password and session length
News: Need to contact the Forum Administrator? e-mail forum.admin@lanciamc.co.uk     -      Copy deadline for Viva Lancia is 12th of each month.      -      For Events e-mail events@lanciamc.co.uk      -      To Join the club go to http://www.lanciamc.co.uk/join.htm
 
   Home   Help Search Calendar Register  
Pages: 1 ... 20 21 22 23 24 [25] 26 27 28 29 30 ... 54   Go Down
  Print  
Author Topic: Story so far series 1 resto  (Read 351722 times)
0 Members and 1 Guest are viewing this topic.
GG
Megaposter
*
Posts: 570



WWW
« Reply #360 on: 13 August, 2016, 01:53:32 PM »

that's the bottom of the block. They are more generously spaced at the top.
And on the Fulvia, these bores are even scalloped, since the pistons aren't ever at the bottom at the same time!
Logged

Appia C10, Flavia 2000 coupe, Fulvia Fanalone
JohnMillham
Lapsed
Permanent resident
**
Posts: 1045



« Reply #361 on: 13 August, 2016, 02:23:23 PM »

that's the bottom of the block. They are more generously spaced at the top.
And on the Fulvia, these bores are even scalloped, since the pistons aren't ever at the bottom at the same time!
Surely, when No. 1 is at the bottom, so is No. 3 and when No. 2 is at the bottom, so is No. 4.
The same goes for the top.
Regards, John
Logged
lancialulu
Press Officer
Permanent resident
*****
Posts: 5050



« Reply #362 on: 13 August, 2016, 03:45:47 PM »

that's the bottom of the block. They are more generously spaced at the top.
And on the Fulvia, these bores are even scalloped, since the pistons aren't ever at the bottom at the same time!
Note to self....must pay more attention!
Logged

Its not the winning but taking part! or is it taking apart?
Lancias:
1955 Aurelia B12
1967 Fulvia 1.3HFR
1972 Fulvia 1600HF
1972 Fulvia Sport 1600
1983 HPE VX
1988 Delta 1.6GTie
1998 Zeta 21.  12v
GG
Megaposter
*
Posts: 570



WWW
« Reply #363 on: 13 August, 2016, 07:27:36 PM »

that's the bottom of the block. They are more generously spaced at the top.
And on the Fulvia, these bores are even scalloped, since the pistons aren't ever at the bottom at the same time!
Surely, when No. 1 is at the bottom, so is No. 3 and when No. 2 is at the bottom, so is No. 4.
The same goes for the top.
Regards, John

Good catch John, but I think you mean that 1/4 are on the bottom at the same time, and so are 2/3.
Model of Appia crank shown below.



* Screen Shot 2016-08-13 at 2.24.15 PM.png (85.74 KB, 867x498 - viewed 545 times.)
Logged

Appia C10, Flavia 2000 coupe, Fulvia Fanalone
neil-yaj396
Committee
Permanent resident
*****
Posts: 1268



« Reply #364 on: 14 August, 2016, 07:43:18 AM »

My gawd those bores look horribly close?Huh??

Quite! Would be interested to see the head gasket?
Logged

1979 1300 Beta Coupe, 2014 Ypsilon 1.2 S Series Momo
JohnMillham
Lapsed
Permanent resident
**
Posts: 1045



« Reply #365 on: 14 August, 2016, 08:42:32 AM »

that's the bottom of the block. They are more generously spaced at the top.
And on the Fulvia, these bores are even scalloped, since the pistons aren't ever at the bottom at the same time!
Surely, when No. 1 is at the bottom, so is No. 3 and when No. 2 is at the bottom, so is No. 4.
The same goes for the top.
Regards, John

Good catch John, but I think you mean that 1/4 are on the bottom at the same time, and so are 2/3.
Model of Appia crank shown below.


It depends on how Lancia numbered the cylinders. The front one on the crankshaft isn't always No. 1. The front one on the Lambda and Augusts are given number 2. No. 1 on the Lambda is the cylinder nearest the driver (on a right hand drive car) and No. 1 on an Augusta is the opposite one, i/e. the front left or second crank pin. I think Lancia did this so that the firing order was always 1,2,3 4! On the Lambda is goes anti-clockwise (seen from the top) and on the Augusta clockwise.
Regards, John
Logged
GG
Megaposter
*
Posts: 570



WWW
« Reply #366 on: 14 August, 2016, 01:49:03 PM »

Thanks for the info, John.Those early cars are tricky.

On the Appia, the workshop manual assigns cylinder #1  to the first journal, and #4 to the last. The owners manual (s.2) says the firing order is 1342 (as shown on the ignition distributor) and that the numbering of cylinders is on the head. Hopefully 1 is still 1, etc.
Logged

Appia C10, Flavia 2000 coupe, Fulvia Fanalone
lancianut666
Permanent resident
**
Posts: 1781


Slow but rough


« Reply #367 on: 15 August, 2016, 08:32:11 PM »

Hi all
just an update...went to see my engine man today as I forgot the crankshaft last week....had a thought before I went over about the core plugs in the bottom of the block....30-40 pounds to replace them I am advised... and he says he will pop the pistons in the block as he was unsure about no 4 with it being back to front...I have to take JCS to get his steristrips taken off tomorrow so I will try and get these couple of jobs done by the end of the week...hopefully...
Clarkey akaJCJ
Logged

Fulvia Coupe S2 Flavia Coupe 1967 1.8 Kugelfischer Prisma 1.6 carb Y10 Fila Y10 Touring Dedra 1.8 Dedra 2.0 Turbo Appia S1
lancianut666
Permanent resident
**
Posts: 1781


Slow but rough


« Reply #368 on: 16 August, 2016, 08:42:27 PM »

pics of the cleaned up pistons and new mains


* 100_0097.JPG (1161.33 KB, 3072x2304 - viewed 500 times.)

* 100_0101.JPG (1311.96 KB, 3072x2304 - viewed 499 times.)

* 100_0097.JPG (1161.33 KB, 3072x2304 - viewed 529 times.)
Logged

Fulvia Coupe S2 Flavia Coupe 1967 1.8 Kugelfischer Prisma 1.6 carb Y10 Fila Y10 Touring Dedra 1.8 Dedra 2.0 Turbo Appia S1
lancianut666
Permanent resident
**
Posts: 1781


Slow but rough


« Reply #369 on: 28 August, 2016, 02:37:13 PM »

Any tips on getting the plugs out of the end of the crank? will they get destroyed in the process?
Clarkey
Logged

Fulvia Coupe S2 Flavia Coupe 1967 1.8 Kugelfischer Prisma 1.6 carb Y10 Fila Y10 Touring Dedra 1.8 Dedra 2.0 Turbo Appia S1
will
Senior Member
*****
Posts: 114



« Reply #370 on: 28 August, 2016, 07:06:02 PM »

I normally hand the crankshaft to engineering shop.
They use a selection of stud extractors so they need to be replaced.
With new plugs there used to be some in consortium store
Logged

Aurelia B20 4th Series Appia 2nd Series  Kappa Coupe 3.0 24v V6
lancianut666
Permanent resident
**
Posts: 1781


Slow but rough


« Reply #371 on: 28 August, 2016, 10:17:24 PM »

I'll check and see if we have any..thanks
Logged

Fulvia Coupe S2 Flavia Coupe 1967 1.8 Kugelfischer Prisma 1.6 carb Y10 Fila Y10 Touring Dedra 1.8 Dedra 2.0 Turbo Appia S1
ben
Lapsed
Megaposter
*
Posts: 456


« Reply #372 on: 29 August, 2016, 11:14:32 AM »

Assuming plugs in the crankshaft are similar to the Aprilia they are aluminium and have to be drilled out very carefully so as not to damage the female threads in the crankshaft.
Start with a small drill centered as accurately as possible and drill right through the plugs then repeat with gradually increased drill sizes until you reach the thread.
If you are lucky the final bit of the plug comes out like a length of curly wire. Then you may need to poke around with something like a dentists probe to get the last bits out and you will need a tap of the correct size to finally clean up the threads before thoroughly washing out the drillings and blowing clean with compressed air.
So not a job to be undertaken lightly but generally considered to be essential if a crank has been re-machined.
I used threaded alloy rod to replace mine on the Aprilia. I think 10mm diameter by 1mm pitch and cut each one off after screwing them in with thread locking compound,finally filing them off smooth.
So as you will see they are certainly not re-usable and you cannot usually get them out with stud extrators.
As Will says probably best to have the machine shop do it but there are a few stories out there about disasters because it has not been done properly.
Ben




Logged
lancianut666
Permanent resident
**
Posts: 1781


Slow but rough


« Reply #373 on: 30 August, 2016, 08:53:37 AM »

thanks for the advice
Logged

Fulvia Coupe S2 Flavia Coupe 1967 1.8 Kugelfischer Prisma 1.6 carb Y10 Fila Y10 Touring Dedra 1.8 Dedra 2.0 Turbo Appia S1
lancianut666
Permanent resident
**
Posts: 1781


Slow but rough


« Reply #374 on: 30 August, 2016, 09:09:38 AM »

so the 2 plugs 28 & 30 are the same thread see pic...what about 31


* crank.jpg (332.04 KB, 1754x1240 - viewed 487 times.)
Logged

Fulvia Coupe S2 Flavia Coupe 1967 1.8 Kugelfischer Prisma 1.6 carb Y10 Fila Y10 Touring Dedra 1.8 Dedra 2.0 Turbo Appia S1
Pages: 1 ... 20 21 22 23 24 [25] 26 27 28 29 30 ... 54   Go Up
  Print  
 
Jump to:  

Contact the Forum Administrator

LMC Forum copyright © 2007 - 2021 Lancia Motor Club Ltd

Powered by SMF 1.1.20 | SMF © 2006-2011, Simple Machines
Page created in 0.071 seconds with 21 queries.