Lancia Motor Club Forum Banner
28 September, 2020, 06:35:28 AM *
Welcome, Guest. Please login or register.

Login with username, password and session length
News: Need to contact the Forum Administrator? e-mail forum.admin@lanciamc.co.uk, for Database Administrator e-mail database.admin@lanciamc.co.uk      -      Copy deadline for Viva Lancia is 12th of each month.      -      For Events e-mail events@lanciamc.co.uk      -      To Join the club go to http://www.lanciamc.co.uk/join.htm
 
   Home   Help Search Calendar Register  
Pages: [1]   Go Down
  Print  
Author Topic: Flavia Hydrovac brake servo required  (Read 1066 times)
0 Members and 1 Guest are viewing this topic.
phil-m
Lapsed
Senior Member
*****
Posts: 173


« on: 04 January, 2013, 04:37:44 PM »

Does anyone have an old Flavia remote servo for sale, the remote Hydrovac type. Mine has developed a bit of a habit for brake fluid so I would like to rebuild another and then swap them over. Any advice on rebuilding would also be greatfuly accepted.
Logged
lancialulu
Press Officer
Permanent resident
*****
Posts: 3980



« Reply #1 on: 04 January, 2013, 06:40:21 PM »

Consortium sell an after-market replacement and Omicron renovate if that helps. It is a weird system - I have just got a Flavia Vig and am going through it before the MOT. I bled the brakes in the normal way without realising you should first start at the slave cylinder. Anyway seemed to be OK and changed the fluid and got the air out.....
Logged

Its not the winning but taking part! or is it taking apart?
1955 Aurelia B12
1967 Flavia Vignale iniezione
1967 Fulvia 1.3HFR
1972 Fulvia 1600HF
1972 Fulvia 1600HF
1972 1600 Fulvia Sport
1979 2500 Gamma Coupe
1988 Delta 1.6GTi
1998 Zeta
ColinMarr
Permanent resident
**
Posts: 1565



« Reply #2 on: 14 January, 2013, 08:49:46 PM »

Phil,

I missed this question when you first raised it sorry. The remote servo fitted to Flavia and Flaminia earned a poor reputation for unreliability, but in my experience a lot of this was unfounded. I successfully rebuilt the servo for my car in the mid 1980s and went on to do two more for others. The system is only marginally more complicated than the dual circuit master-cylinders fitted to Flavia and Fulvia it you are OK with that then doing the servo should be no more problematic.

The most common fault was brake fluid getting past the seals at the vacuum chamber end of the unit, into the chamber and then into the inlet tract with lots of white smoke in the exhaust to prove it!

One of the problems then was the lack of seals. Rebuild kits were not available in the UK and at least two of the cup seals seemed to be almost unique to this system. I searched through the parts bins of a motor factor that was supposedly a Lockheed agent and I found cup seals that did the job, others were simple o rings that were easy to obtain.

Another problem was that the design of this system involved a side-shoot from the main cylinder going off at an angle (and hence blind) to the air filter, so that it was impossible to push the piston out with a wooden dowel. The trick (leaned from the wizard Tony Amato) was to tap the flange end of the side-tube with a pin-hammer until low-and-behold the piston with its o ring rises up out of the housing until you can grip it to pull it out. Any slight damage to the flange needs to be flattened out.

Cleaning up the bores with very fine abrasive paper, fitting new seals and putting it all back together seemed to complete the job.

Of course, you may now find an alternative remote unit off the shelf, but when I did it that wasn't an option.

Good luck!

Colin
Logged
Pages: [1]   Go Up
  Print  
 
Jump to:  

Contact the Forum Administrator

LMC Forum copyright © 2007 - 2018 Lancia Motor Club Ltd

Powered by SMF 1.1.20 | SMF © 2006-2011, Simple Machines
Page created in 0.049 seconds with 20 queries.