Richard Fridd
Permanent resident
Posts: 3487
|
|
« Reply #195 on: 02 November, 2012, 11:39:33 AM » |
|
I should put a few miles on before anything else. Seatbelts to be fitted also.In the correspondance which came with the car there is mention of mounting points "in the upper rear panel". I can't see any ! Advice welcome once again. Richard
|
|
|
Logged
|
Richard Nevison Fridd Happy Lancia, Happy Life
|
|
|
Richard Fridd
Permanent resident
Posts: 3487
|
|
« Reply #196 on: 02 November, 2012, 04:10:14 PM » |
|
hi John,thanks for the offer of the rebuild company details. I assume the Kurtis is an oval racer. richard
|
|
|
Logged
|
Richard Nevison Fridd Happy Lancia, Happy Life
|
|
|
Richard Fridd
Permanent resident
Posts: 3487
|
|
« Reply #197 on: 10 November, 2012, 02:07:32 PM » |
|
Discs now machined
|
|
|
Logged
|
Richard Nevison Fridd Happy Lancia, Happy Life
|
|
|
LanciAlan
Megaposter
Posts: 379
|
|
« Reply #198 on: 10 November, 2012, 02:37:22 PM » |
|
Lovely. You would think they might clean up the other surfaces too while they were at it!
|
|
|
Logged
|
Alan Murphy
Lancias that begin with "F" ... and affordable variants beginning with "Z" and "P" ..... and now with added "Y"!
|
|
|
Richard Fridd
Permanent resident
Posts: 3487
|
|
« Reply #199 on: 10 November, 2012, 03:58:28 PM » |
|
As there was no charge from the machine shop I will be happy to clean the other surfaces myself. I understand the discs had developed particularly hard surfaces being cast iron. richard
|
|
|
Logged
|
Richard Nevison Fridd Happy Lancia, Happy Life
|
|
|
JohnMillham
Lapsed
Permanent resident
Posts: 1045
|
|
« Reply #200 on: 10 November, 2012, 04:39:48 PM » |
|
hi John,thanks for the offer of the rebuild company details. I assume the Kurtis is an oval racer. richard
Yes - and it's now on its way to the U.K. 4.7 litre V8 and weighing about 1400 pounds - it should go like the clappers! In 2006, the bearing rebuilding firm made an excellent job of the complicated bearing which holds the Lambda pinion in place. They are:- H B Precision Engineers Ltd., Riverside Works, Honley, Holmfirth, Huddersfield, HD9 6PQ Tel:- 01484 665 116, E-mail:- sales@hb-bearings.comWebsite:- www.hb-bearings.com Regards, John
|
|
|
Logged
|
|
|
|
Richard Fridd
Permanent resident
Posts: 3487
|
|
« Reply #201 on: 13 November, 2012, 04:36:19 PM » |
|
Thanks John. Back to the question of seat belts,there were no mounting points so some have been made and belts fitted
|
|
|
Logged
|
Richard Nevison Fridd Happy Lancia, Happy Life
|
|
|
Richard Fridd
Permanent resident
Posts: 3487
|
|
« Reply #202 on: 31 January, 2013, 05:35:34 PM » |
|
Front hubs reunited with discs, ready to be refitted
|
|
« Last Edit: 02 May, 2013, 02:05:55 PM by Richard Fridd »
|
Logged
|
Richard Nevison Fridd Happy Lancia, Happy Life
|
|
|
Richard Fridd
Permanent resident
Posts: 3487
|
|
« Reply #203 on: 21 March, 2013, 05:52:26 PM » |
|
A few small jobs done recently. I have installed an ammeter under the dash to monitor the charging system and installed a rear fog lamp. The fog lamp is operated by a temporary switch in the cigar lighter apperture. When I find a Flaminia PF wiper switch I will use that instead (with a remote warning lamp) which should suit the dash better. Something else I might change is the fuel filter. In it's place I woulld like to try a combined filter/pressure regulator(with glass bowl) as fitted to some other Flaminia models along with an electric fuel pump for primig. One other thing I have done is route the engine breather pipes to a catch tank rather than into the airfilter housing.
|
|
« Last Edit: 18 April, 2013, 02:55:29 PM by Richard Fridd »
|
Logged
|
Richard Nevison Fridd Happy Lancia, Happy Life
|
|
|
Richard Fridd
Permanent resident
Posts: 3487
|
|
« Reply #204 on: 06 April, 2013, 07:15:18 AM » |
|
I have now found a switch from my jumble of spares. By good fortune the knob of the now spare lighter has the same thread. So will need to install a fog lamp warning lamp somewhere next.
|
|
« Last Edit: 06 April, 2013, 09:26:32 AM by Richard Fridd »
|
Logged
|
Richard Nevison Fridd Happy Lancia, Happy Life
|
|
|
Parisien
|
|
« Reply #205 on: 06 April, 2013, 07:20:53 AM » |
|
Richard, I must go back to the start of your 14 page thread and work through it.... P
|
|
|
Logged
|
Frank Gallagher
|
|
|
Richard Fridd
Permanent resident
Posts: 3487
|
|
« Reply #206 on: 14 April, 2013, 12:44:55 PM » |
|
I would like to replace the rear discs soon, with the pair which I have had machined. Can anyone tell me if this job can be done with the tranaxle in situ? Best Regards Rchard
|
|
« Last Edit: 18 April, 2013, 02:45:08 PM by Richard Fridd »
|
Logged
|
Richard Nevison Fridd Happy Lancia, Happy Life
|
|
|
Richard Fridd
Permanent resident
Posts: 3487
|
|
« Reply #207 on: 02 May, 2013, 06:42:17 PM » |
|
Existing rear discs still in service, but new brake pipes fitted at rear, and brake piston assemblies stripped, cleaned and refitted
|
|
« Last Edit: 02 May, 2013, 07:50:15 PM by Richard Fridd »
|
Logged
|
Richard Nevison Fridd Happy Lancia, Happy Life
|
|
|
lancialulu
|
|
« Reply #208 on: 02 May, 2013, 07:59:38 PM » |
|
Have you left some fingers behind??
|
|
|
Logged
|
Its not the winning but taking part! or is it taking apart? Lancias: 1955 Aurelia B12 1967 Fulvia 1.3HFR 1972 Fulvia 1600HF 1972 Fulvia Sport 1600 1983 HPE VX 1988 Delta 1.6GTie 1998 Zeta 21. 12v
|
|
|
Parisien
|
|
« Reply #209 on: 02 May, 2013, 08:00:51 PM » |
|
Very funny......just noticed that...... P
|
|
|
Logged
|
Frank Gallagher
|
|
|
|