davidwheeler
Permanent resident
Posts: 1331
|
 |
« Reply #30 on: 18 October, 2017, 03:52:06 PM » |
|
Spark plugs (transferred from discussion elsewhere in Lambda) NGK BP5HS seem to be the ones for VIIth and VIIIth at least.
|
|
|
|
|
Logged
|
David Wheeler. Lambdas, Aprilia, Fulvia Sport.(formerly Appia and Thema as well).
|
|
|
GG
Megaposter
Posts: 488
B20 s.2, Appia C10 unrestored
|
|
« Reply #31 on: 18 October, 2017, 03:53:59 PM » |
|
Bearing lists, one nice original from RIV
Any idea of the dates of these? Thanks. |
|
|
|
|
Logged
|
B20 s.2, Appia C10 unrestored
|
|
|
davidwheeler
Permanent resident
Posts: 1331
|
|
« Reply #32 on: 25 October, 2019, 11:55:23 AM » |
|
Lambda wiring diagram VII+ series.
|
|
|
|
Logged
|
David Wheeler. Lambdas, Aprilia, Fulvia Sport.(formerly Appia and Thema as well).
|
|
|
davidwheeler
Permanent resident
Posts: 1331
|
|
« Reply #33 on: 02 December, 2019, 01:15:38 PM » |
|
Autovac = Le Nivex fuel pump according to The Modern Motor Mechanic 1955
|
|
|
|
Logged
|
David Wheeler. Lambdas, Aprilia, Fulvia Sport.(formerly Appia and Thema as well).
|
|
|
davidwheeler
Permanent resident
Posts: 1331
|
|
« Reply #34 on: 01 December, 2020, 10:54:05 PM » |
|
Australian VIIIth undertray sketch
|
|
|
|
Logged
|
David Wheeler. Lambdas, Aprilia, Fulvia Sport.(formerly Appia and Thema as well).
|
|
|
davidwheeler
Permanent resident
Posts: 1331
|
|
« Reply #35 on: 01 June, 2022, 11:04:47 AM » |
|
Fitting new stubaxle/pillars.
Remove springs etc. and lower guide 111008 as per instructions in the Book.
Fit sleeve 101014 screwing it down an inch or so.
Tap dpwnwards using a suitable drift (such as a block of wood) by a few mm in order to remove screw 10721 which is hiding at the back. You can then unscrew 101058 - providing it is not seized!
101012 then is removed upwards. It is likely to be seized so tap it downwards until it is free then clean and lubricate it. You can then fit a suitable tubular spacer and draw it upwards with 101014.
Insert new pillar assembly making sure you include ring 101058 above the stub axle and rings 111097 and 111009 below it.
Refit bottom sleeve 111008.
Refit sleeve 101012, using 101014 screwed on a bit if you need to tap it down. Make sure the hole for the screw 10721 is in the right position.
Tap it down a few mm. past its proper place and screw on 101058 fully into place (it goes to the end of the thread), fit screw 10721 but not too tight, then draw the sleeve back up into place with 101014. Tighten the screw and the sleeve is now properly fitted.
Fit thrust bearing and shield and sleeve 101011. These all slide down inside 101012.
Fill the shock absorber with oil if you have not already done so.
Insert the springs and re-assemble the top end as per the Book.
I found I had to draw up the damper rod 101034 using the spring extractor tool because it was too had a pull by hand unlike the old and presumably worn original in order to fit 101041.
|
|
|
« Last Edit: 01 June, 2022, 11:10:08 AM by davidwheeler »
|
Logged
|
David Wheeler. Lambdas, Aprilia, Fulvia Sport.(formerly Appia and Thema as well).
|
|
|
davidwheeler
Permanent resident
Posts: 1331
|
|
« Reply #36 on: 21 June, 2022, 07:06:40 PM » |
|
Check camber and castor with spacer and set square with bubble level before installing springs.
|
|
|
|
Logged
|
David Wheeler. Lambdas, Aprilia, Fulvia Sport.(formerly Appia and Thema as well).
|
|
|
|
