Lancia Motor Club Forum Banner
01 July, 2022, 07:35:53 PM *
Welcome, Guest. Please login or register.

Login with username, password and session length
News: Need to contact the Forum Administrator? e-mail forum.admin@lanciamc.co.uk, for Database Administrator e-mail database.admin@lanciamc.co.uk      -      Copy deadline for Viva Lancia is 12th of each month.      -      For Events e-mail events@lanciamc.co.uk      -      To Join the club go to http://www.lanciamc.co.uk/join.htm
 
   Home   Help Search Calendar Register  
Pages: 1 2 [3]   Go Down
  Print  
Author Topic: Technical data only  (Read 24873 times)
0 Members and 1 Guest are viewing this topic.
davidwheeler
Permanent resident
**
Posts: 1331



« Reply #30 on: 18 October, 2017, 03:52:06 PM »

Spark plugs (transferred from discussion elsewhere in Lambda)  NGK BP5HS seem to be the ones for VIIth and VIIIth at least.
Logged

David Wheeler.  Lambdas, Aprilia, Fulvia Sport.(formerly Appia and Thema as well).
GG
Megaposter
*
Posts: 490


B20 s.2, Appia C10 unrestored


WWW
« Reply #31 on: 18 October, 2017, 03:53:59 PM »

Bearing lists, one nice original from RIV

Any idea of the dates of these? Thanks.
Logged

B20 s.2, Appia C10 unrestored
davidwheeler
Permanent resident
**
Posts: 1331



« Reply #32 on: 25 October, 2019, 11:55:23 AM »

Lambda wiring diagram VII+ series.


* Lambda wiring.jpg (451.03 KB, 1824x2100 - viewed 332 times.)
Logged

David Wheeler.  Lambdas, Aprilia, Fulvia Sport.(formerly Appia and Thema as well).
davidwheeler
Permanent resident
**
Posts: 1331



« Reply #33 on: 02 December, 2019, 01:15:38 PM »

Autovac = Le Nivex fuel pump according to The Modern Motor Mechanic 1955


* IMG (Copy).jpg (91.7 KB, 521x768 - viewed 422 times.)

* IMG_0001 (Copy).jpg (64.5 KB, 565x768 - viewed 465 times.)

* IMG_0002 (Copy).jpg (108.92 KB, 500x768 - viewed 421 times.)

* IMG_0003 (Copy).jpg (136.89 KB, 541x768 - viewed 416 times.)

* IMG_0004 (Copy).jpg (148.26 KB, 528x768 - viewed 392 times.)

* IMG_0005 (Copy).jpg (129.62 KB, 536x768 - viewed 400 times.)
Logged

David Wheeler.  Lambdas, Aprilia, Fulvia Sport.(formerly Appia and Thema as well).
davidwheeler
Permanent resident
**
Posts: 1331



« Reply #34 on: 01 December, 2020, 10:54:05 PM »

Australian VIIIth undertray sketch

* 8th series undertray sketch.pdf (728.05 KB - downloaded 141 times.)
Logged

David Wheeler.  Lambdas, Aprilia, Fulvia Sport.(formerly Appia and Thema as well).
davidwheeler
Permanent resident
**
Posts: 1331



« Reply #35 on: 01 June, 2022, 11:04:47 AM »

Fitting new stubaxle/pillars.
Remove springs etc. and lower guide 111008 as per instructions in the Book.
Fit sleeve 101014 screwing it down an inch or so.
Tap dpwnwards using a suitable drift (such as a block of wood) by a few mm in order to remove screw 10721 which is hiding at the back.  You can then unscrew 101058 - providing it is not seized!  
101012 then is removed upwards.     It is likely to be seized so tap it downwards until it is free then clean and lubricate it.  You can then fit a suitable tubular spacer and draw it upwards with 101014.
Insert new pillar assembly making sure you include ring 101058 above the stub axle and rings 111097 and 111009 below it.
Refit bottom sleeve 111008.
Refit sleeve 101012, using 101014 screwed on a bit if you need to tap it down.   Make sure the hole for the screw 10721 is in the right position.
Tap it down a few mm. past its proper place and screw on 101058 fully into place (it goes to the end of the thread), fit screw 10721 but not too tight, then draw the sleeve back up into place with 101014.   Tighten the screw and the sleeve is now properly fitted.
Fit thrust bearing and shield and sleeve 101011.  These all slide down inside 101012.
Fill the shock absorber with oil if you have not already done so.
Insert the springs and re-assemble the top end as per the Book.      
I found I had to draw up the damper rod 101034 using the spring extractor tool because it was too had a pull by hand unlike the old and presumably worn original in order to fit 101041.


* IMG_0001 (Copy).jpg (99.79 KB, 632x1080 - viewed 11 times.)

* IMG_0698 (Copy).JPG (258.31 KB, 774x1080 - viewed 11 times.)

* IMG_0703 (Copy).JPG (274.87 KB, 810x1080 - viewed 11 times.)

* IMG_0706 (Copy).JPG (246.13 KB, 810x1080 - viewed 10 times.)

* IMG_0708 (Copy).JPG (165.79 KB, 543x1080 - viewed 10 times.)

* IMG_0709 (Copy).JPG (215.62 KB, 665x1080 - viewed 11 times.)
« Last Edit: 01 June, 2022, 11:10:08 AM by davidwheeler » Logged

David Wheeler.  Lambdas, Aprilia, Fulvia Sport.(formerly Appia and Thema as well).
davidwheeler
Permanent resident
**
Posts: 1331



« Reply #36 on: 21 June, 2022, 07:06:40 PM »

Check camber and castor with spacer and set square with bubble level before installing springs.


* IMG_0710 (Copy).JPG (328.47 KB, 1440x1080 - viewed 9 times.)

* IMG_0714 (Copy).JPG (314.34 KB, 1440x1080 - viewed 8 times.)
Logged

David Wheeler.  Lambdas, Aprilia, Fulvia Sport.(formerly Appia and Thema as well).
Pages: 1 2 [3]   Go Up
  Print  
 
Jump to:  

Contact the Forum Administrator

LMC Forum copyright © 2007 - 2021 Lancia Motor Club Ltd

Powered by SMF 1.1.20 | SMF © 2006-2011, Simple Machines
Page created in 0.06 seconds with 20 queries.