Lancia Motor Club Forum Banner
01 November, 2024, 09:01:29 PM *
Welcome, Guest. Please login or register.

Login with username, password and session length
News: Need to contact the Forum Administrator? e-mail forum.admin@lanciamc.co.uk     -      Copy deadline for Viva Lancia is 12th of each month.      -      For Events e-mail events@lanciamc.co.uk      -      To Join the club go to http://www.lanciamc.co.uk/join.htm
 
   Home   Help Search Calendar Register  
Pages: [1]   Go Down
  Print  
Author Topic: next job.  (Read 5959 times)
0 Members and 1 Guest are viewing this topic.
bill
Guest
« on: 23 June, 2009, 07:35:15 PM »

first of all thank you for replies on brake querie. finished the welding today and undersealing. tomorrow bleed the brakes.
reg.the bleed nipples:one thing I would like to mention again it may help someone, use the usual wd40 then tap  the metal on the caliper. tap the end of the nipple and finally slowly pour a kettleful of boiling water over the caliper leave for a few mins then slowly unscrew the nipple it really works.

next questions and I hope they make sense re. the carbs. running rough.

starting from the rad.the first choke there is a raised round ali. female opening next to the identification tag. should this have a brass taperd screw as choke no. three? also just noticed this today where the carbs mount the manifold the rubber appears to be split. I tried to put a feeler gauge in and I think it was hitting some thing solid, could air be sucked in causing the carbs to run rough? if this is so can you still buy the rubber seals? I hope this makes sense.
once again thanks to, all I really appreciate the help.

bill.
Logged
ncundy
Lapsed
Rebel Poster
*
Posts: 980



« Reply #1 on: 23 June, 2009, 11:06:06 PM »

Splits in the rubber are common if the support arm under the carbs is not secure. They are still easily available from places like Omicron etc but cost about £100 IIRC.
Logged

1969 Fanalone, Mazda RX-8, Fiat Multipla
fay66
Permanent resident
**
Posts: 6227



« Reply #2 on: 24 June, 2009, 12:11:20 AM »

first of all thank you for replies on brake querie. finished the welding today and undersealing. tomorrow bleed the brakes.
reg.the bleed nipples:one thing I would like to mention again it may help someone, use the usual wd40 then tap  the metal on the caliper. tap the end of the nipple and finally slowly pour a kettleful of boiling water over the caliper leave for a few mins then slowly unscrew the nipple it really works.

next questions and I hope they make sense re. the carbs. running rough.

starting from the rad.the first choke there is a raised round ali. female opening next to the identification tag. should this have a brass taperd screw as choke no. three? also just noticed this today where the carbs mount the manifold the rubber appears to be split. I tried to put a feeler gauge in and I think it was hitting some thing solid, could air be sucked in causing the carbs to run rough? if this is so can you still buy the rubber seals? I hope this makes sense.
once again thanks to, all I really appreciate the help.

bill.

Probably not the same as mine but here are the pages regarding the Solex Carbs on my Fulvia 2c Berlina of 1091cc capacity.

Brian
8227 Cool


* img740 copy.jpg (114.89 KB, 600x824 - viewed 430 times.)

* img741 copy.jpg (159.44 KB, 600x824 - viewed 425 times.)

* img742 copy.jpg (79.05 KB, 600x824 - viewed 467 times.)
Logged

Own 1966 Fulvia 2C Berlina since 1997, back on road 11-1999.Known as "Fay"
2006 Renault Megane 1 5 Dci Sports Tourer
Dedra Technical Adviser
davidwheeler
Permanent resident
**
Posts: 1479



« Reply #3 on: 24 June, 2009, 06:44:40 PM »

I repaired my rubbers with some particularly ferocious windscreen fixing stuff I got from my local supplier.  It is like black mastic but plasticy rather than rubbery and sets "hard" and is called Arbomast Auograde windscreen sealing compound.  It is impossible to get off once it has set so be careful where you put it.
David.
Logged

David Wheeler.  Lambdas, Aprilia, Fulvia Sport.(formerly Appia and Thema as well).
rogerelias
Rebel Poster
*
Posts: 955


MY 1600HF IN HEARTBEAT GARAGE


« Reply #4 on: 24 June, 2009, 07:00:46 PM »

We use a similar product at work for replacing windscreens, its so strong we glued the apprentices moped wheel to the tarmac,  and it held, had to cut with a knife to let him go home, but was great fun watching his moped getting nowhere. Grin
Logged

FULVIA 1600HF LUSSO
1958 VELOCETTE MAC
Triumph Bonneville t120v 1972
1968 MGC ROADSTER
1958 Series 2 Appia berlina
fay66
Permanent resident
**
Posts: 6227



« Reply #5 on: 24 June, 2009, 07:03:29 PM »

We use a similar product at work for replacing windscreens, its so strong we glued the apprentices moped wheel to the tarmac,  and it held, had to cut with a knife to let him go home, but was great fun watching his moped getting nowhere. Grin

I'll make sure I don't leave my Raleigh Moped anywhere near you then Roger Grin

Brian
8227 Cool
Logged

Own 1966 Fulvia 2C Berlina since 1997, back on road 11-1999.Known as "Fay"
2006 Renault Megane 1 5 Dci Sports Tourer
Dedra Technical Adviser
bill
Guest
« Reply #6 on: 24 June, 2009, 07:16:39 PM »

hi david, reg.the sealing compound would I have to remove the carbs. or can this be done in situ. is it the type of thing halfords may have or is it a specialised item?

thank you bill.

(amazing what you learn on this forum)
Logged
nistri
Megaposter
*
Posts: 560


« Reply #7 on: 29 June, 2009, 12:53:29 PM »

To repair the carb rubber support is necessary to remove it and glue it as indicated in previous messages. Be careful not to damage the various gaskets.Carbs will need rebalancing after reassembly and refitting of the support bar securing them to the oil filter base. Good luck, Andrea
Logged

Andrea Nistri

Ardea S2
Appia S2
Fulvia GTE
Fulvia Sport 1.3 S
Fulvia Montecarlo
Fulvia Coupe 1.3 S
fay66
Permanent resident
**
Posts: 6227



« Reply #8 on: 29 June, 2009, 02:41:47 PM »

Bill,
is your rubber mounting all one piece or two seperate items, ie one per Carburettor? I have 1 nearly new item suitable for 1 carburettor 35mm, marked S441/A1108053. if your interested.

Brian
8227 Cool
Logged

Own 1966 Fulvia 2C Berlina since 1997, back on road 11-1999.Known as "Fay"
2006 Renault Megane 1 5 Dci Sports Tourer
Dedra Technical Adviser
bill
Guest
« Reply #9 on: 29 June, 2009, 07:46:10 PM »

hi brian, thank you for the e mail I have tried to contact Goeff when I send the e mail my computer keeps shutting down. I am not  good on these things, I only hope it has went through.
just had a look at the sandwich gasket althouth it is a little dark in my garage I think it is all one peice.

the car is coming along well cleaning the seats so getting excited.  just the carb to sort and double check the brakes for air locks before I do anything else.

not sure where to place this. had a great day yesterday (sunday) marshaling on the tyneside stages on the otterburn ranges. not sure how many members have ever been to a tarmac rally like this but they are not to be missed. if you have the chance to attend one.this is scary stuff the speed of the cars (no lancias) is unreal the no 1 car was a wrc hyundi what a car. I was watching as the driver left he took the revs. of the clock the noise was fantastic, when he dropped the clutch the car left like a bullet out of a gun fantatic.

cheers.

bill
Logged
Pages: [1]   Go Up
  Print  
 
Jump to:  

Contact the Forum Administrator

LMC Forum copyright © 2007 - 2021 Lancia Motor Club Ltd

Powered by SMF 1.1.20 | SMF © 2006-2011, Simple Machines
Page created in 0.06 seconds with 21 queries.