Lancia Motor Club Forum Banner
04 December, 2024, 06:13:30 PM *
Welcome, Guest. Please login or register.

Login with username, password and session length
News: Need to contact the Forum Administrator? e-mail forum.admin@lanciamc.co.uk     -      Copy deadline for Viva Lancia is 12th of each month.      -      For Events e-mail events@lanciamc.co.uk      -      To Join the club go to http://www.lanciamc.co.uk/join.htm
 
   Home   Help Search Calendar Register  
Pages: [1]   Go Down
  Print  
Author Topic: Aprilia bottom gear  (Read 5630 times)
0 Members and 1 Guest are viewing this topic.
davidwheeler
Permanent resident
**
Posts: 1485



« on: 24 June, 2009, 06:34:54 PM »

My gearbox struggles continue - the gears I have in at the moment still fall out of third and now top as well despite new bearings, which means the box must come out again some time.  So, I would like to fit a new bottom gear pinion.  I suspect that means I shall have to get one made or at least repaired.
1.  Any advice.
2. Anyone interested in a batch.
David
Logged

David Wheeler.  Lambdas, Aprilia, Fulvia Sport.(formerly Appia and Thema as well).
davidwheeler
Permanent resident
**
Posts: 1485



« Reply #1 on: 08 July, 2009, 04:52:29 PM »

I have decided to make some bottom gears pinions 38 19525 as repair is not an option.  The spare I have to hand is short and requires two spacers.  It seems to have been made that way.  The one in the car is longer, as in the drawing and needs only one spacer 38 19523 and I think it would be preferable to use this as a pattern.  Please could anyone lend me one?


* Aprilia gearbox layshaft 125 Kb.jpg (125.15 KB, 1000x622 - viewed 484 times.)
Logged

David Wheeler.  Lambdas, Aprilia, Fulvia Sport.(formerly Appia and Thema as well).
davidwheeler
Permanent resident
**
Posts: 1485



« Reply #2 on: 12 April, 2010, 04:26:59 PM »

I have at last achieved success with what has turned out to be a very difficult task.  Apparently, the gears are of a strange profile and the only way to make them is to wire cut them from hardened steel on a computer controlled machine.  This is expensive!  I am going to take delivery of a sample gear in the next few days and will try it in a box.  THIS IS A SERIES 1 GEAR.  The series 2 has a different number of teeth and I doubt if they are interchangeable.

I shall buy one for £250.  A batch of 5 will cost £200 apiece.  All Aprilia bottom gears are worn out, how about it chaps?  After all, Aprilias now sell for £20K.

David
Logged

David Wheeler.  Lambdas, Aprilia, Fulvia Sport.(formerly Appia and Thema as well).
davidwheeler
Permanent resident
**
Posts: 1485



« Reply #3 on: 05 May, 2010, 08:44:31 AM »

The sample fits and I am now getting a gear made and hardened.  I shall fit it and be there at the Sliding Pillar I hope.  As this is being made on a CAD wire cutting machine, the program will be available in case anyone else needs a gear.  I shall make a small charge for the use of it!
Logged

David Wheeler.  Lambdas, Aprilia, Fulvia Sport.(formerly Appia and Thema as well).
davidwheeler
Permanent resident
**
Posts: 1485



« Reply #4 on: 09 June, 2010, 08:49:48 AM »

Bottom gear now fitted and functioning very well.   Still the noise of straight cut gears but without the horrid grinding of the old worn one.    Made in Carlisle on a CC lathe for £250 + VAT.   Pattern exists in computer so further copies may be a little cheaper.
Logged

David Wheeler.  Lambdas, Aprilia, Fulvia Sport.(formerly Appia and Thema as well).
davidwheeler
Permanent resident
**
Posts: 1485



« Reply #5 on: 10 June, 2010, 08:28:30 AM »

I have also posted recommendations for engine machining, piston ring manufacture, engine balancing and radiator manufacture on the Lambda Technical Information thread
Logged

David Wheeler.  Lambdas, Aprilia, Fulvia Sport.(formerly Appia and Thema as well).
davidwheeler
Permanent resident
**
Posts: 1485



« Reply #6 on: 10 June, 2010, 08:35:19 AM »

I also tackled the third/top gear problem.  In my box of bits I found a slightly rusty third gear pair and sleeve.  I looked closely at them for the first time in many years and could not see any signs of wear.  Faintly, a dim memory surfaced of my first trip to Torino in Old Boot (or F*rting Annie as she was then) in 1971 and a trip to Cavalitto when I bought a new Aprilia head and valves and a carburettor.  I also bought third gears!  After a little fettling they were fitted and moving sweetly.
Behold, silent gears that I no longer have to hold in place!  I've also managed to stop the engine oil leaks by pinching an unworn sump and engine end plates from another engine.  The new new big ends do not rattle and oil pressure is superb.
See you at the Sliding Pillar.
Logged

David Wheeler.  Lambdas, Aprilia, Fulvia Sport.(formerly Appia and Thema as well).
davidwheeler
Permanent resident
**
Posts: 1485



« Reply #7 on: 18 February, 2011, 03:49:05 PM »

Alas, the engineers chose the wrong material/hardening parameters for the bottom gear pinion and the teeth have gone.  Does anybody know the correct specifications?
Meantime, I have fitted a reasonable gear from the toy-box.   This has taken some time owing to certain arcane differences.  In order to prevent myself (and perhaps others) making the same mistakes I have posted details on the technical information only thread, q.v. but please do not comment there (unless strictly relevant).
Logged

David Wheeler.  Lambdas, Aprilia, Fulvia Sport.(formerly Appia and Thema as well).
Pages: [1]   Go Up
  Print  
 
Jump to:  

Contact the Forum Administrator

LMC Forum copyright © 2007 - 2021 Lancia Motor Club Ltd

Powered by SMF 1.1.20 | SMF © 2006-2011, Simple Machines
Page created in 0.044 seconds with 20 queries.