Lancia Motor Club Forum Banner
06 June, 2020, 03:42:33 PM *
Welcome, Guest. Please login or register.

Login with username, password and session length
News: Need to contact the Forum Administrator? e-mail forum.admin@lanciamc.co.uk, for Database Administrator e-mail database.admin@lanciamc.co.uk      -      Copy deadline for Viva Lancia is 12th of each month.      -      For Events e-mail events@lanciamc.co.uk      -      To Join the club go to http://www.lanciamc.co.uk/join.htm
 
   Home   Help Search Calendar Register  
Pages: [1]   Go Down
  Print  
Author Topic: what capacity  (Read 2848 times)
0 Members and 1 Guest are viewing this topic.
bill
Guest
« on: 02 June, 2009, 04:09:42 PM »

hi, have my rad. back hope to fit it tomorrow. do I need any special coolant? and what capacity is the cooling system? any tips on bleeding the system or is it striaght forward?

also can anyone help with oil filter? I have taken mine off as it is a little rusty the only letters and nos. I can see are, ocar -49 0170.

 thank you bill.
Logged
ncundy
Lapsed
Rebel Poster
*
Posts: 980



« Reply #1 on: 02 June, 2009, 05:15:34 PM »

For an S2 1.3 its 6.3 litres (including heater). You need to make sure that the thermostat has cracked and the heater matrix is full by operating the heater valve. If filling from scratch I removed the temperature sensor in the top water rail (behind the thermostat) to help it bleed. You can fill from here as well, it's fiddly but it can get the highest point free of air if you need. Remember to put it back before you start it !

Logged

1969 Fanalone, Mazda RX-8, Fiat Multipla
Richard Fridd
Permanent resident
**
Posts: 2900



« Reply #2 on: 02 June, 2009, 05:24:41 PM »

coolant capacity 6.3Ltrs for 1.3 and 7Ltrs for 1.6 engines respectively.use 30%antifreeze/70%water.this is according to the fulvia concise shop manual.i normally mix the water +antifreeze in advance then pour into COLD radiator,start engine and top up till warm squeezing the hoses,refit the rad cap, run engine till hot ,check temp guage+feel rad which should be hot by now.also check rad fan operates-a manual overide switch may be a useful addition to electric fans-also check heater matrix and its drip tray+drain pipe for condition+operation.i had mine recored along with the rad  
Logged

Richard Nevison Fridd
Jai Sharma
Megaposter
*
Posts: 374


« Reply #3 on: 02 June, 2009, 09:49:34 PM »

On the oil filter front "ocar" was once Tecnocar. I believe, as I have bought them from motor factor shops before, that the Fulvia oil filter was the same as used on Rover V8 though someone might shoot me down in flames if my memory is wrong! They won't have a tecnocar one though. These are certainly available from Omicron and probably elsewhere.
I understand some filters (not tecnocar) allow the oil to drain out of them which is not good on start-up.
Logged
fay66
Permanent resident
**
Posts: 5823



« Reply #4 on: 03 June, 2009, 12:46:48 AM »

I've just bought 2 oil filters for my Fulvia 2c from Omicron at 7.85 +Vat+P&P

Supplied were Omicron part number 2300672U Fulvia Oil Filter UFI/Fram.although the part number on the box itself is 2310202.

On the box it says comparativa
Fiaam FT4863
Fram PH 2821A
Mann & H W 940/24
Purolator PC 237-OC 37
Technocar R 49.

Filter x 2 = 15.70
post           6.50 (pretty weighty!)
Vat            3.34

Total cost 25.54

The same filter has been used by myself without any problems at all for something like 10 years.

In fact I have seen this same filter advertised on ebay for considerably more than what I pay Omicron.

Brian
8227 Cool   
Logged

Own 1966 Fulvia 2C Berlina since 1997, back on road 11-1999.Known as "Fay"
1999 Suzuki Wagon R+ GL, now my daughters
2006 Renault Megane 1 5 Dci Sports Tourer
Dedra Technical Adviser
lancialulu
Press Officer
Permanent resident
*****
Posts: 3841



« Reply #5 on: 03 June, 2009, 06:41:29 AM »

Brian

My motor factors in Colchester is a Fram Stockist and has Fram PH 2821A(well 1) on their shelf I ordered another 6 as they were 5.40p ea!!!!

Tim
Logged

Its not the winning but taking part! or is it taking apart?
1955 Aurelia B12
1967 Flavia Vignale iniezione
1967 Fulvia 1.3HFR
1972 Fulvia 1600HF
1972 Fulvia 1600HF
1972 1600 Fulvia Sport
1979 2500 Gamma Coupe
1988 Delta 1.6GTi
1998 Zeta
nistri
Megaposter
*
Posts: 301


« Reply #6 on: 03 June, 2009, 12:03:32 PM »

The manual gives the capacity of the whole system. Quite a lot of coolant (more than one liter) is however in the engine. Unless the engine is taken apart, it is virtually impossible to refill the system with 6 or 7 liters. Good idea to backflush the system via the hose joining the drain cock at the back . I do this regularly every 24 months. Andrea
Logged

Andrea Nistri

Ardea S2
Appia S2
Fulvia GTE
Fulvia Sport 1.3 S
Fulvia Montecarlo
Fulvia Coupe 1.3 S
fay66
Permanent resident
**
Posts: 5823



« Reply #7 on: 03 June, 2009, 12:19:52 PM »

Brian

My motor factors in Colchester is a Fram Stockist and has Fram PH 2821A(well 1) on their shelf I ordered another 6 as they were 5.40p ea!!!!

Tim

As Bruce Forsyth used to say, "Didn't he do well" pretty good price that, I take it no problemm with the Fram item?

Brian
8227 Cool
Logged

Own 1966 Fulvia 2C Berlina since 1997, back on road 11-1999.Known as "Fay"
1999 Suzuki Wagon R+ GL, now my daughters
2006 Renault Megane 1 5 Dci Sports Tourer
Dedra Technical Adviser
lancialulu
Press Officer
Permanent resident
*****
Posts: 3841



« Reply #8 on: 03 June, 2009, 02:11:54 PM »

Brian, I am advised they are made in Italy as are most by same manufacturer as your list indicates!!!! Same internals - Fram is a really top brand so I suspect the annual filter change is not a stressed component!

Tim
Logged

Its not the winning but taking part! or is it taking apart?
1955 Aurelia B12
1967 Flavia Vignale iniezione
1967 Fulvia 1.3HFR
1972 Fulvia 1600HF
1972 Fulvia 1600HF
1972 1600 Fulvia Sport
1979 2500 Gamma Coupe
1988 Delta 1.6GTi
1998 Zeta
Pages: [1]   Go Up
  Print  
 
Jump to:  

Contact the Forum Administrator

LMC Forum copyright © 2007 - 2018 Lancia Motor Club Ltd

Powered by SMF 1.1.20 | SMF © 2006-2011, Simple Machines
Page created in 0.039 seconds with 21 queries.