Lancia Motor Club Forum Banner
10 November, 2024, 03:17:22 AM *
Welcome, Guest. Please login or register.

Login with username, password and session length
News: Need to contact the Forum Administrator? e-mail forum.admin@lanciamc.co.uk     -      Copy deadline for Viva Lancia is 12th of each month.      -      For Events e-mail events@lanciamc.co.uk      -      To Join the club go to http://www.lanciamc.co.uk/join.htm
 
   Home   Help Search Calendar Register  
Pages: [1]   Go Down
  Print  
Author Topic: Gasket to leading edge of Fulvia bonnet  (Read 1269 times)
0 Members and 1 Guest are viewing this topic.
RRomanis
Member
***
Posts: 26


« on: 19 January, 2024, 03:46:44 PM »

Hi,
Can anyone advise on the purpose of the rubber gasket that is supposed to be fitted to the leading edge of a Fulvia bonnet?  I've attempted to attach an image from the Tavola, but I'm not sure it's worked.....
I don't recall having ever seen this installed on any car...?  So perhaps it's not too important.
Looking at my own bonnet (which is aluminium) there's no obvious place for it to be fitted, or means by which it would be fixed.
The reason I ask is that at speed, my bonnet does flap about a bit, which can be a bit disconcerting, and I'm wondering if the gasket may assist in preventing this.
I suspect the answer is no, as this is the purpose of the 2 height adjustable rubber grommets at the front corners of the bonnet opening, but I'd appreciate views from those more knowledgable.
Thanks, Robert


* Bonnet gasket.png (168.43 KB, 551x354 - viewed 281 times.)
Logged
Beckerman67
Member
****
Posts: 82



« Reply #1 on: 19 January, 2024, 05:05:40 PM »

 This was discussed in "Report on (slow) S2 Coupe rebuild progress" by Norm Thomas.
 On page 38 there are a couple of photos.
 I guess its purpose is as a weather-seal?
« Last Edit: 20 January, 2024, 04:17:12 AM by Beckerman67 » Logged
Jai Sharma
Megaposter
*
Posts: 475


« Reply #2 on: 20 January, 2024, 11:13:24 AM »

I have definitely seen them in place. Not sure I'd rush to put them back on a steel bonnet if the car is used in the wet a lot.
Logged
lancialulu
Press Officer
Permanent resident
*****
Posts: 5038



« Reply #3 on: 20 January, 2024, 12:09:48 PM »

They should be there. Lancia always had a good reason.
Logged

Its not the winning but taking part! or is it taking apart?
Lancias:
1955 Aurelia B12
1967 Fulvia 1.3HFR
1972 Fulvia 1600HF
1972 Fulvia Sport 1600
1983 HPE VX
1988 Delta 1.6GTie
1998 Zeta 21.  12v
nthomas1
Rebel Poster
*
Posts: 855



« Reply #4 on: 20 January, 2024, 04:13:27 PM »


The later TAV shows the seals and metal fitting strips more clearly.   As suggested above, page 38 of my "slow S2 rebuild" thread makes reference on page 38.   The TAV diagram also shows the cover strips for the side flanges of the bonnet, item 56, which I also fitted to my car but have never ever seen on another Fulvia!


* Screenshot 2024-01-20 at 16.02.43.png (860.68 KB, 1020x682 - viewed 67 times.)
Logged

Norm Thomas
Ormskirk, Lancashire

Own:
1973 Fulvia S2 Coupe
Previous Lancias: S2 Coupe and S3 Coupe in late 1970s
Keithver
Senior Member
*****
Posts: 144



« Reply #5 on: 26 January, 2024, 12:56:39 PM »

I took this photo (shows the front RHS corner of the bonnet) of another Fulvia as a reference for when I did mine. I was told the strips aid with waterproofing the engine bay. The rubber is glued to the steel strip


* IMG_1331a.JPG (510.11 KB, 1512x2016 - viewed 67 times.)
Logged

'72 series 2 Fulvia 1,3s
nthomas1
Rebel Poster
*
Posts: 855



« Reply #6 on: 26 January, 2024, 04:33:18 PM »

Here are three pictures of my S2 Coupe.  The first shows one of the two slightly curved metal angle strips fastened in place with 3 stainless screws.  The second shows the rubber seal glued in behind the metal strip, and overlapping at the end.   The third shows the finished job, with the outer ends of the seals trimmed for better location when the bonnet is closed. 


* a MG_0079 copy.JPG (619.02 KB, 2126x1139 - viewed 72 times.)

* b IMG_0158 copy.JPG (942.87 KB, 2409x1807 - viewed 74 times.)

* c IMG_0130 copy.JPG (950.84 KB, 2409x1187 - viewed 68 times.)
Logged

Norm Thomas
Ormskirk, Lancashire

Own:
1973 Fulvia S2 Coupe
Previous Lancias: S2 Coupe and S3 Coupe in late 1970s
RRomanis
Member
***
Posts: 26


« Reply #7 on: 26 January, 2024, 09:11:39 PM »

Really helpful
Thanks all
Robert
Logged
Pages: [1]   Go Up
  Print  
 
Jump to:  

Contact the Forum Administrator

LMC Forum copyright © 2007 - 2021 Lancia Motor Club Ltd

Powered by SMF 1.1.20 | SMF © 2006-2011, Simple Machines
Page created in 0.045 seconds with 21 queries.