Lancia Motor Club Forum Banner
12 December, 2024, 11:31:49 PM *
Welcome, Guest. Please login or register.

Login with username, password and session length
News: Need to contact the Forum Administrator? e-mail forum.admin@lanciamc.co.uk     -      Copy deadline for Viva Lancia is 12th of each month.      -      For Events e-mail events@lanciamc.co.uk      -      To Join the club go to http://www.lanciamc.co.uk/join.htm
 
   Home   Help Search Calendar Register  
Pages: [1]   Go Down
  Print  
Author Topic: Stiff gear lever 1965 S1  (Read 1352 times)
0 Members and 1 Guest are viewing this topic.
ColinRob
Lapsed
Member
**
Posts: 10


« on: 07 June, 2023, 04:28:26 PM »

I am reviving my Fulvia after the winter - long story! A no-start was resolved by priming the fuel lines from the mechanical pump and topping up the float
bowls that were dry. Next issue was that I could only engage first and second gears and am reluctant to remove the car from storage if I cannot reverse it back into place
as space is very restricted.

After looking at an old post on here I have tried lubricating the gear lever mechanism from the front of the car and by removing the rubber gaiter to get access from inside. Squirts of WD40 have loosened it up but it remains reluctant to move in the horizontal plane to move from second to third and equally difficult to engage reverse. I plan to get the car out, jack it up and give it better lubrication with some grease.

I have the parts diagram of the gear linkage assembly but am a little puzzled as to how it actually works.

Can anyone here describe it or point me to a good explanation? Also, is it possible to properly lubricate and examine it without dropping the subframe?

Thanks for any help.

Logged
lancialulu
Press Officer
Permanent resident
*****
Posts: 5056



« Reply #1 on: 07 June, 2023, 08:51:55 PM »

I think you will need to take the external shift mechanism off the car and dismantle. There is a steel rod that goes through an alloy housing and this corrodes due to different metals. Over time this makes reverse in particular difficult to select as you need this rod to rotate. Wd40 will not get close to this corrosion, if this is the fault.
Logged

Its not the winning but taking part! or is it taking apart?
Lancias:
1955 Aurelia B12
1967 Fulvia 1.3HFR
1972 Fulvia 1600HF
1972 Fulvia Sport 1600
1983 HPE VX
1988 Delta 1.6GTie
1998 Zeta 21.  12v
ColinRob
Lapsed
Member
**
Posts: 10


« Reply #2 on: 08 June, 2023, 11:29:12 AM »

Thanks for the reply.

Is it possible to remove the shift lever mechanism without dropping the sub-frame?
Logged
lancialulu
Press Officer
Permanent resident
*****
Posts: 5056



« Reply #3 on: 08 June, 2023, 01:00:24 PM »

it is unless the nuts (one of them is a countersunk hex) are seized. You might want to put a jack under the gearbox and remove the rear mount. and also loosen / undo the central mount to tilt the engine / gearbox rearwards/down. Care not to do too much as it wll strain the water hoses and fan may foul the radiator.

Easier to drop the gearbox not the subframe if you can get the car on a lift and have a transmission jack/cradle
Logged

Its not the winning but taking part! or is it taking apart?
Lancias:
1955 Aurelia B12
1967 Fulvia 1.3HFR
1972 Fulvia 1600HF
1972 Fulvia Sport 1600
1983 HPE VX
1988 Delta 1.6GTie
1998 Zeta 21.  12v
ColinRob
Lapsed
Member
**
Posts: 10


« Reply #4 on: 10 June, 2023, 08:44:56 PM »

Thanks. I have got the lever to engage all gears but it is not exactly slick so will see how best to tackle it further - I don't have a lift.
Logged
Pages: [1]   Go Up
  Print  
 
Jump to:  

Contact the Forum Administrator

LMC Forum copyright © 2007 - 2021 Lancia Motor Club Ltd

Powered by SMF 1.1.20 | SMF © 2006-2011, Simple Machines
Page created in 0.03 seconds with 20 queries.