HBG
Megaposter
Posts: 295
|
|
« Reply #15 on: 15 May, 2023, 11:03:05 AM » |
|
Thanks Andrea, Tim.
The heater valve moves nicely and the heater blows hot and cold on demand. It could be that the cable is 'too short' so won't go all the way to the left. I can live with this for now but I'd like to fix the lever. I'll look around as Andrea suggests. Sugru also comes to mind....
|
|
|
Logged
|
|
|
|
Beckerman67
|
|
« Reply #16 on: 15 May, 2023, 11:53:56 AM » |
|
|
|
« Last Edit: 15 May, 2023, 12:05:02 PM by Beckerman67 »
|
Logged
|
|
|
|
HBG
Megaposter
Posts: 295
|
|
« Reply #17 on: 15 May, 2023, 09:52:03 PM » |
|
I wonder how you fit them? Think I'll try and make one from Milliput or similar.
Could do with a picture of the top lever if anyone has?
Thanks 8
|
|
|
Logged
|
|
|
|
nthomas1
Rebel Poster
Posts: 859
|
|
« Reply #18 on: 17 May, 2023, 12:55:06 PM » |
|
Here are some pictures of the levers.
|
|
|
Logged
|
Norm Thomas Ormskirk, Lancashire
Own: 1973 Fulvia S2 Coupe Previous Lancias: S2 Coupe and S3 Coupe in late 1970s
|
|
|
HBG
Megaposter
Posts: 295
|
|
« Reply #19 on: 17 May, 2023, 04:00:51 PM » |
|
Thanks Norm. Looks like the top lever is the same as the bottom lever, just inverted. I'm going to look into mould making so I can model one out of Milliput. It's a small part that doesn't affect the car greatly, but I do like a project.
|
|
|
Logged
|
|
|
|
Wangler
Megaposter
Posts: 310
|
|
« Reply #20 on: 17 May, 2023, 07:18:45 PM » |
|
Wow, a full set of unbroken levers for a Fulvia. Now that’s a rare sight!
|
|
|
Logged
|
Fulvia Coupe 1976 Fulvia Coupe 3 1975
|
|
|
nthomas1
Rebel Poster
Posts: 859
|
|
« Reply #21 on: 18 May, 2023, 08:47:06 AM » |
|
Wow, a full set of unbroken levers for a Fulvia. Now that’s a rare sight!
Two good ones came with the car, two are courtesy of Omicron!
|
|
|
Logged
|
Norm Thomas Ormskirk, Lancashire
Own: 1973 Fulvia S2 Coupe Previous Lancias: S2 Coupe and S3 Coupe in late 1970s
|
|
|
nthomas1
Rebel Poster
Posts: 859
|
|
« Reply #22 on: 18 May, 2023, 08:51:31 AM » |
|
Thanks Norm. Looks like the top lever is the same as the bottom lever, just inverted. I'm going to look into mould making so I can model one out of Milliput. It's a small part that doesn't affect the car greatly, but I do like a project.
It will be interesting to see how you get on. For information, my top and bottom levers (the same part as you say) were bought from Omicron for £38 each a couple of years back, plus vat and shipping of course.
|
|
|
Logged
|
Norm Thomas Ormskirk, Lancashire
Own: 1973 Fulvia S2 Coupe Previous Lancias: S2 Coupe and S3 Coupe in late 1970s
|
|
|
HBG
Megaposter
Posts: 295
|
|
« Reply #23 on: 31 May, 2023, 07:06:39 PM » |
|
Here's a few pics of my job to add an end to the heater lever.
First make a cast of the lower lever with 'Blue stuff'. Heat it in hot water and it goes soft. When cool it goes hard. Ish.
|
|
|
Logged
|
|
|
|
HBG
Megaposter
Posts: 295
|
|
« Reply #24 on: 31 May, 2023, 07:08:51 PM » |
|
Use Milliput in the mould to make the part.
|
|
|
Logged
|
|
|
|
HBG
Megaposter
Posts: 295
|
|
« Reply #25 on: 31 May, 2023, 07:12:42 PM » |
|
Clean up the lever still fitted to the car. Used a Dremel, carefully.
|
|
|
Logged
|
|
|
|
HBG
Megaposter
Posts: 295
|
|
« Reply #26 on: 31 May, 2023, 07:16:57 PM » |
|
Slot the new end with a Dremel. Should have been a dentist. Glue it on with epoxy, leaving the sides clear for more Milliput.
|
|
|
Logged
|
|
|
|
HBG
Megaposter
Posts: 295
|
|
« Reply #27 on: 31 May, 2023, 07:17:43 PM » |
|
Glued on.
|
|
|
Logged
|
|
|
|
HBG
Megaposter
Posts: 295
|
|
« Reply #28 on: 31 May, 2023, 07:23:18 PM » |
|
Can't find the pic of the finished job! Tomorrow!
|
|
|
Logged
|
|
|
|
HBG
Megaposter
Posts: 295
|
|
« Reply #29 on: 02 June, 2023, 07:17:27 PM » |
|
Here it is. Not perfect but until I have to dismantle the dash top I'm happy.
|
|
|
Logged
|
|
|
|
|