Lancia Motor Club Forum Banner
11 December, 2024, 04:52:42 PM *
Welcome, Guest. Please login or register.

Login with username, password and session length
News: Need to contact the Forum Administrator? e-mail forum.admin@lanciamc.co.uk     -      Copy deadline for Viva Lancia is 12th of each month.      -      For Events e-mail events@lanciamc.co.uk      -      To Join the club go to http://www.lanciamc.co.uk/join.htm
 
   Home   Help Search Calendar Register  
Pages: [1]   Go Down
  Print  
Author Topic: Aprilia fuel gauge  (Read 4575 times)
0 Members and 1 Guest are viewing this topic.
peterblenk
Member
****
Posts: 57


« on: 14 August, 2019, 10:11:36 AM »

Does anyone have drawings, sketches, or photos to show how the sender mechanism goes together? Also, is there a source for parts - especially the large Mazak piece? The two I have are crumbling and also warped.
peterblenk@aol.com
Logged
GeoffJohnson
Member
***
Posts: 45


« Reply #1 on: 14 August, 2019, 12:12:26 PM »

Hi Peter
Here is a sketch I did of the fuel gauge sender that I did some time ago to remind me how it worked.
Hope it helps

Geoff Johnson


* sender.JPG (96.67 KB, 794x1123 - viewed 491 times.)
Logged
Mikenoangelo
Megaposter
*
Posts: 465


« Reply #2 on: 14 August, 2019, 02:28:51 PM »

Blimey that's even worse than the one on the Augusta!

Mike
Logged
davidwheeler
Permanent resident
**
Posts: 1485



« Reply #3 on: 17 August, 2019, 08:55:06 AM »

Thanks, Geoff, I have posted it on the technical information thread.
Logged

David Wheeler.  Lambdas, Aprilia, Fulvia Sport.(formerly Appia and Thema as well).
peterblenk
Member
****
Posts: 57


« Reply #4 on: 16 September, 2019, 05:35:40 PM »

Thank you, Geoff; this is very helpful. I am told that
someone, perhaps in Switzerland, made new ones. Any idea who that could be? I was thinking that it might be possible to scan and 3-D print the offending Mazak part in a better material, such as aluminium. Peter
Logged
williamcorke
Rebel Poster
*
Posts: 714


B10


« Reply #5 on: 03 February, 2023, 02:38:47 PM »

I'm resuscitating this topic to (as far as possible) keep Aprilia fuel gauge/sender info in one place on the forum.

My car has the early round instrument, but I believe the ALIT sender unit is the same for the later rectangular gauge.

The restoration of my system - at both ends of the car - has progressed to the point where there are now just 2 unsolved problems.

1. The sender is missing the 'rotating spring contact' show in Geoff Johnson's very useful diagram in this thread. Can someone provide a photo of a correct one? All I can find as reference is Photo 1 below, which has what looks like a homemade replacement (in steel or even aluminium?). How is the contact finger attached to the rotating barrel-shaped piece?

Incidentally, I don’t think the longer contact finger in the photo is correct - it would earth the circuit. Perhaps is a retainer for the cover not shown in the photo. Whatever, my unit doesn’t have this part.

2. I am having trouble finding replacement bulbs for the gauge. The glass on the originals is 9mm in diameter - with no 'bulge' to their shape. The replacements I've sourced from two different places are 11mm or 12mm and so won't fit into the tubes within the unit that lead to each of the indicator lights. Photo 2 below shows 3 replacements on the left and the 3 working original ones I have on the right. Does anyone know of source for these 6v bulbs, or has perhaps found an LED type that is narrow enough to fit?





* Screenshot 2023-02-03 at 14.31.36.png (1104.44 KB, 1000x736 - viewed 130 times.)

* Screenshot 2023-02-03 at 14.32.02.png (906.22 KB, 1000x524 - viewed 120 times.)
Logged

'37 Aprilia
'50 B10
'53 B20
'68 Flavia Vignale
'55 Giulietta Sprint
S1 Land Rover
simonandjuliet
Permanent resident
**
Posts: 2559



« Reply #6 on: 05 February, 2023, 09:32:13 AM »

William, a few photos and suggestions !

The bulbs were too tall, but since the tops were plastic, I cut them down to fit behind the unit

Let me know if you want more detail or dimensions for the tank unit parts (I don't think that I have a spare but I'll have a look)

BTW there is a short pin hat goes through the axle of the disk that holds it in place on the top plate. The pin is then held in place by the groove on the underside of the insulating contact "needle"

Poorly explained but if you want more detail I will try and improve my description !


* IMG_2548.jpeg (244.66 KB, 960x1280 - viewed 127 times.)

* IMG_2549.jpeg (348.43 KB, 960x1280 - viewed 129 times.)

* IMG_2550.jpeg (283.55 KB, 960x1280 - viewed 122 times.)

* IMG_2551.jpeg (263.99 KB, 960x1280 - viewed 128 times.)

* IMG_2552.jpeg (319.23 KB, 960x1280 - viewed 129 times.)

* IMG_2553.jpeg (169.15 KB, 960x1280 - viewed 122 times.)

* IMG_2554.jpeg (201.78 KB, 960x1280 - viewed 121 times.)

* Screenshot 2023-02-05 at 10.22.05.png (1109.17 KB, 1960x1034 - viewed 124 times.)
Logged

AmilcarCGS, ApriliaCabrio,S2Aprilia, 2xArdea c'cino,S4 Ardea, Appia c'cino, Appia f'cino,B20s4,R4 Sinpar, R4 Rodeo, 65 Moke, 3xR60 Tractor, 2xToselli 78, Moto Guzzi Ercole,LR Defender, Mini ALL4 JCW, Moto Guzzi Cardellino, Fulvia GT, RE Himalayan
williamcorke
Rebel Poster
*
Posts: 714


B10


« Reply #7 on: 05 February, 2023, 07:17:42 PM »

Perfect, thank you Simon,

I've ordered the bulbs and the photos of the 'finger' are what I need to make a replacement, which I think could be soldered to the top of the top of the 'cap' (whose locating pin I'd already replaced).

Am I right in thinking that the finger should be on the contact for the first of the 9 light (5 litres) when the float is at the bottom of its range of travel?
Logged

'37 Aprilia
'50 B10
'53 B20
'68 Flavia Vignale
'55 Giulietta Sprint
S1 Land Rover
williamcorke
Rebel Poster
*
Posts: 714


B10


« Reply #8 on: 09 February, 2023, 12:35:35 PM »

Update - bulbs have arrived, slightly different shape to Simon's (Photo 1) and required no modification to fit perfectly. Now to make the 'moving finger'.  There are a few electrical bits of construction I'm going to have to get into including, if no-one can help me out from their parts stores, two of the 3 dash light brackets.

James Parry has kindly found one of the pieces I need (Photo 2) but I need another the same as this, and also the central clip-in bulb mount (Photo 3) which carries the two bulbs for the warning lights (dynamo and indicators).

If any of you can help, please let me know, otherwise I'll be testing my fiddly fabrication skills (though nothing can be worse than trafficator wiring!).


* Screenshot 2023-02-09 at 12.25.51.png (844.68 KB, 1860x1038 - viewed 119 times.)

* Screenshot 2023-02-09 at 12.34.27.png (852.31 KB, 1274x690 - viewed 121 times.)

* Screenshot 2023-02-09 at 12.33.51.png (631.7 KB, 638x982 - viewed 113 times.)
« Last Edit: 09 February, 2023, 03:21:30 PM by williamcorke » Logged

'37 Aprilia
'50 B10
'53 B20
'68 Flavia Vignale
'55 Giulietta Sprint
S1 Land Rover
Pages: [1]   Go Up
  Print  
 
Jump to:  

Contact the Forum Administrator

LMC Forum copyright © 2007 - 2021 Lancia Motor Club Ltd

Powered by SMF 1.1.20 | SMF © 2006-2011, Simple Machines
Page created in 0.043 seconds with 21 queries.