Lancia Motor Club Forum Banner
28 March, 2024, 04:32:12 PM *
Welcome, Guest. Please login or register.

Login with username, password and session length
News: Need to contact the Forum Administrator? e-mail forum.admin@lanciamc.co.uk, for Database Administrator e-mail database.admin@lanciamc.co.uk      -      Copy deadline for Viva Lancia is 12th of each month.      -      For Events e-mail events@lanciamc.co.uk      -      To Join the club go to http://www.lanciamc.co.uk/join.htm
 
   Home   Help Search Calendar Register  
Pages: [1] 2   Go Down
  Print  
Author Topic: Front suspension  (Read 3561 times)
0 Members and 1 Guest are viewing this topic.
davidwheeler
Permanent resident
**
Posts: 1469



« on: 15 May, 2022, 06:19:11 PM »

Starting to install the new pillar/stub axle assemblies.  I find I cannot remove the pillar because it fouls the frame.    I am thinking I will have to remove the screwed in sleeve ("guide tube according to parts list").  Thing is, Freyja and I did this in the garage at Sacro Monte and I canot remember how we did it.
The locking ring at the bottom is dam' tight.  I think I may have to use a little heat after I have made a suitable spaniard to fit it. 


* IMG_0693 (Copy).JPG (287.15 KB, 810x1080 - viewed 84 times.)

* IMG_0695 (Copy).JPG (297.18 KB, 1440x1080 - viewed 87 times.)

* DSCF7676a (Copy).jpg (660.44 KB, 1440x1080 - viewed 85 times.)

* IMG_0001.jpg (318.1 KB, 1289x2201 - viewed 84 times.)
Logged

David Wheeler.  Lambdas, Aprilia, Fulvia Sport.(formerly Appia and Thema as well).
JohnMillham
Permanent resident
**
Posts: 1045



« Reply #1 on: 16 May, 2022, 07:11:06 AM »

Yes, the sleeve has to be removed first. It will only just come out then! Good luck.
Logged
davidwheeler
Permanent resident
**
Posts: 1469



« Reply #2 on: 17 May, 2022, 04:43:50 AM »

Thanks, John.  Do they screw in or just slide in like the bottom ones?
Logged

David Wheeler.  Lambdas, Aprilia, Fulvia Sport.(formerly Appia and Thema as well).
JohnMillham
Permanent resident
**
Posts: 1045



« Reply #3 on: 17 May, 2022, 07:21:52 AM »

When the ring 101058 is undone, it will slide out.
Logged
davidwheeler
Permanent resident
**
Posts: 1469



« Reply #4 on: 17 May, 2022, 04:00:26 PM »

101012 upwards or downwards?
I removed the ring 101058, having made a tool and applied a lot of heat and force.   It would have come easier if I had known about the locking pin 10721 hidden at the back which pinged out after a few turns.
I have tried pulling it out using a 5mm spacer and 101014 to pull upon it, thinking it would come once it started to move.  No such luck.  "Slide out" is not in its vocabulary.    It has shifted a couple of mm. but with great difficulty.     Either I have to make a thicker spacer or install 101014 and tap it downwards.   Pulling it up would seem better...
I do not remember such struggles when Freyja and I did it on the other side in Sacro Monte!
Logged

David Wheeler.  Lambdas, Aprilia, Fulvia Sport.(formerly Appia and Thema as well).
JohnMillham
Permanent resident
**
Posts: 1045



« Reply #5 on: 17 May, 2022, 07:07:11 PM »

I think it slides up when the bottom ring is undone, but it was a while ago when I had mine apart, so I could be wrong. You might have to tap it a bit to persuade it.
Logged
davidwheeler
Permanent resident
**
Posts: 1469



« Reply #6 on: 18 May, 2022, 12:36:49 PM »

Finally got it off this morning.  The sleeve was so tight I had to hammer the spanner to try to extract it (using a spacer made from an old ball bearing) so I tapped it down, cleaned it all and then drew it upwards easily.  When I do the other side I will take pictures and post it in the technical thread.
Logged

David Wheeler.  Lambdas, Aprilia, Fulvia Sport.(formerly Appia and Thema as well).
davidwheeler
Permanent resident
**
Posts: 1469



« Reply #7 on: 24 May, 2022, 08:09:39 PM »

Fitting new spring thrust bearings and wondering what grease - very thick "axle grease" or moly which is thinner but higher shear.   Any ideas?
Logged

David Wheeler.  Lambdas, Aprilia, Fulvia Sport.(formerly Appia and Thema as well).
JohnMillham
Permanent resident
**
Posts: 1045



« Reply #8 on: 25 May, 2022, 09:50:09 AM »

I think they live in oil. Were they not covered in oil when you removed them? If not, I suppose Moly would do the job best.
Logged
donw
Megaposter
*
Posts: 581



« Reply #9 on: 25 May, 2022, 06:26:58 PM »

Looking forward to seeing the"other" side before I start on mine!
Logged

Don Williamson
Member 111 joined 26th July 1963
1917 Theta 2str
1926 Lambda torpedo
1930 Artena berlina
1933 Belna coupe
davidwheeler
Permanent resident
**
Posts: 1469



« Reply #10 on: 01 June, 2022, 10:45:55 AM »

Done.  Full instructions in technical information thread.
Logged

David Wheeler.  Lambdas, Aprilia, Fulvia Sport.(formerly Appia and Thema as well).
davidwheeler
Permanent resident
**
Posts: 1469



« Reply #11 on: 21 June, 2022, 07:05:11 PM »

Whilst installing the new pillars I took advantage of the opportunity to determine the true angles (camber and castor) of the pillars themselves with the aid of a right angles bubble level and a spacer.   Not the most successful photographs - I need to make an appointment with Zaphod Beeblebrock's surgeon to have an extra arm fitted.


* IMG_0710 (Copy).JPG (328.47 KB, 1440x1080 - viewed 78 times.)

* IMG_0714 (Copy).JPG (314.34 KB, 1440x1080 - viewed 83 times.)
Logged

David Wheeler.  Lambdas, Aprilia, Fulvia Sport.(formerly Appia and Thema as well).
GG
Megaposter
*
Posts: 552



WWW
« Reply #12 on: 22 June, 2022, 02:21:06 PM »

Marc Bondini, Australian Aurelia guru, found some "angle measuring gizmo" that was about 1 ½" square and magnetic, and you could just snap it onto the vertical element, and it would tell you its angle.... he got them off Amazon.....
Logged

B20 s.2, Appia C10, Flavia 2000
davidwheeler
Permanent resident
**
Posts: 1469



« Reply #13 on: 23 June, 2022, 12:50:45 PM »

Cheaper than a third arm, too.
Logged

David Wheeler.  Lambdas, Aprilia, Fulvia Sport.(formerly Appia and Thema as well).
williamcorke
Rebel Poster
*
Posts: 681


B10


« Reply #14 on: 23 June, 2022, 02:20:17 PM »

Perhaps something like this?
https://www.amazon.co.uk/AUTOUTLET-Inclinometer-Protractor-Backlight-Magnetic/dp/B07D8TJF4P/ref=sr_1_18?crid=20GQLZ617521X&keywords=inclination+gauge+magnetic&qid=1655993942&sprefix=inclination+gauge+magnetic%2Caps%2C62&sr=8-18
Logged

'37 Aprilia
'50 B10
'53 B20
'68 Flavia Vignale
'55 Giulietta Sprint
S1 Land Rover
Pages: [1] 2   Go Up
  Print  
 
Jump to:  

Contact the Forum Administrator

LMC Forum copyright © 2007 - 2021 Lancia Motor Club Ltd

Powered by SMF 1.1.20 | SMF © 2006-2011, Simple Machines
Page created in 0.063 seconds with 21 queries.