|
my69S1
|
 |
« on: 29 December, 2021, 03:08:43 PM » |
|
Can anyone tell me what these holes are for, two on the inside wheel well arch on both sides. The lower drivers side looks to have been a hold down for something but I don't know what. Or maybe a past owner put these holes in for something? Any help would be appreciated. I'm either missing things or I need to close these holes up. Thanks. Car is a '69 S1.
|
|
|
|
Logged
|
|
|
|
Richard Fridd
Permanent resident
Posts: 3478
|
|
« Reply #1 on: 29 December, 2021, 03:44:44 PM » |
|
2nd photo - fuel tank breather plastic tank?
|
|
|
« Last Edit: 29 December, 2021, 06:26:17 PM by Richard Fridd »
|
Logged
|
Richard Nevison Fridd Happy Lancia, Happy Life
|
|
|
nistri
Megaposter
Posts: 558
|
|
« Reply #2 on: 29 December, 2021, 05:56:25 PM » |
|
They are made to inject antirust solutions like Waxoyl, Andrea
|
|
|
|
|
Logged
|
Andrea Nistri
Ardea S2
Appia S2
Fulvia GTE
Fulvia Sport 1.3 S
Fulvia Montecarlo
Fulvia Coupe 1.3 S
|
|
|
|
my69S1
|
|
« Reply #3 on: 29 December, 2021, 06:45:04 PM » |
|
2nd photo - fuel tank breather plastic tank?
Thanks Richard. Do you have a picture showing how this should be mounted and where the breather tubes go? |
|
|
|
|
Logged
|
|
|
|
|
my69S1
|
|
« Reply #4 on: 29 December, 2021, 06:46:15 PM » |
|
They are made to inject antirust solutions like Waxoyl, Andrea
Andrea, which holes specifically? Do they get plugged when not in use? Should the holes not be the same on each side? |
|
|
|
|
Logged
|
|
|
|
Richard Fridd
Permanent resident
Posts: 3478
|
|
« Reply #5 on: 29 December, 2021, 10:09:51 PM » |
|
Tank breather outlet and then vents to atmosphere via filler neck from distant
memory?
|
|
|
|
|
Logged
|
Richard Nevison Fridd Happy Lancia, Happy Life
|
|
|
|
lancialulu
|
|
« Reply #6 on: 30 December, 2021, 08:39:57 AM » |
|
On rhs on top of the inner wing should be a plastic breather box. The breather pipe from this box exits through the floor along side the drain pipe from the filler pipe enclosure. These are c12mm cavis benz clear plastic piping.
The lower hole on rhs I have always assumed was part of jigging for manufacture. On lhs the photo is not very clear but could have been to do with mounting of an electric car aerial?
|
|
|
|
|
Logged
|
Its not the winning but taking part! or is it taking apart?
Lancias:
1955 Aurelia B12
1967 Fulvia 1.3HFR
1972 Fulvia 1600HF
1972 Fulvia Sport 1600
1983 HPE VX
1988 Delta 1.6GTie
1998 Zeta 21. 12v
|
|
|
nistri
Megaposter
Posts: 558
|
|
« Reply #7 on: 30 December, 2021, 04:10:19 PM » |
|
In the boot there are several holes normally not plugged for injecting antirust solution into the space near the inner wings. On the righthand side near the filler tube there are also holes to fix the petrol breather system. Andrea
|
|
|
|
|
Logged
|
Andrea Nistri
Ardea S2
Appia S2
Fulvia GTE
Fulvia Sport 1.3 S
Fulvia Montecarlo
Fulvia Coupe 1.3 S
|
|
|
Richard Fridd
Permanent resident
Posts: 3478
|
|
« Reply #8 on: 30 December, 2021, 05:39:05 PM » |
|
2nd photo - fuel tank breather plastic tank?
Thanks Richard. Do you have a picture showing how this should be mounted and where the breather tubes go? Only this to go with previous posts. Richard |
|
|
|
Logged
|
Richard Nevison Fridd Happy Lancia, Happy Life
|
|
|
nthomas1
Rebel Poster
Posts: 854
|
|
« Reply #9 on: 31 December, 2021, 11:16:53 AM » |
|
Here's a picture of my S2 Coupe boot showing the pipes in position.
|
|
|
|
Logged
|
Norm Thomas
Ormskirk, Lancashire
Own:
1973 Fulvia S2 Coupe
Previous Lancias: S2 Coupe and S3 Coupe in late 1970s
|
|
|
|
my69S1
|
|
« Reply #10 on: 31 December, 2021, 03:34:55 PM » |
|
Thanks everyone for the assist. Great picture Norm.
|
|
|
|
|
Logged
|
|
|
|
|
