Lancia Motor Club Forum Banner
10 November, 2024, 03:28:27 AM *
Welcome, Guest. Please login or register.

Login with username, password and session length
News: Need to contact the Forum Administrator? e-mail forum.admin@lanciamc.co.uk     -      Copy deadline for Viva Lancia is 12th of each month.      -      For Events e-mail events@lanciamc.co.uk      -      To Join the club go to http://www.lanciamc.co.uk/join.htm
 
   Home   Help Search Calendar Register  
Pages: 1 [2]   Go Down
  Print  
Author Topic: S3 master cylinder  (Read 12521 times)
0 Members and 1 Guest are viewing this topic.
ian
Guest
« Reply #15 on: 27 May, 2008, 10:32:51 PM »

Rear calipers replaced with refurbished units, although all the shims fell out, 3 on one side, 4 on the other? not to sure which one goes where. Any ideas Scarpia? Embarrassed  I filled the master cylinder on the car with dot 4 brake fluid bleed through the recommended way with no problems, using an old easy bleed system I had knocking about. Air filter and oil filter sourced. Forgot about a sump plug tool, any alternatives? Is the plug used by any other marques or will I have to buy the right one? Sump sits very low doesn't it!
Logged
Scarpia
Lapsed
Rebel Poster
*
Posts: 723



« Reply #16 on: 28 May, 2008, 05:41:12 PM »

Quote
make sure you watch for the shim washers that fall out from between the calipers and the mounting points when you remove the bolts

The problem with experience is that you gain it mostly just after you needed it. Like I said , the same thing happened to me. I seem to remember using feeler guages, a bit of trial and error, wheel spinning to check free movement and tiny blobs of copper grease to glue the washers in position while I put the bolts in. Sounds right anyway......
i'll check the book later for the spacing required, pad to disc and tolerance allowed.
Logged
Richard Fridd
Permanent resident
**
Posts: 3484



« Reply #17 on: 28 May, 2008, 06:09:57 PM »

i normally use a suitable hexagonal wrench to rotate the sump drain plug - being careful not to lose the associated copper seal unless i have a new one to hand-
Logged

Richard Nevison Fridd                                                                      Happy Lancia, Happy Life
Neil Lewis
Guest
« Reply #18 on: 28 May, 2008, 06:54:11 PM »

Quote
make sure you watch for the shim washers that fall out from between the calipers and the mounting points when you remove the bolts

I seem to remember using feeler gauges, a bit of trial and error, wheel spinning to check free movement and tiny blobs of copper grease to glue the washers in position while I put the bolts in. Sounds right anyway......

I also used the trial-and-"improvement" method (political correctness gone mad) and just put the shim in so that there was as equal amount of space on both side of the disk between itself and the calipers.  Being as though there are pistons on both sides of the disk, so long as you have space both sides, the calipers will never move closer to the disk and start to rub.  So I say forget the book and just go by eye and feel.  It works for me.

Most importantly, don't forget the tab washers under the bolt heads.  I did and a front caliper came off on the M3 and nearly ruined a wheel.  The bolt of course was lost and there wasn't another M10 fine bolt I could borrow from elsewhere on the car so I had to come home on an RAC truck.  Most undignified.

Neil
Logged
Pages: 1 [2]   Go Up
  Print  
 
Jump to:  

Contact the Forum Administrator

LMC Forum copyright © 2007 - 2021 Lancia Motor Club Ltd

Powered by SMF 1.1.20 | SMF © 2006-2011, Simple Machines
Page created in 0.051 seconds with 21 queries.