Lancia Motor Club Forum Banner
13 November, 2024, 03:29:02 PM *
Welcome, Guest. Please login or register.

Login with username, password and session length
News: Need to contact the Forum Administrator? e-mail forum.admin@lanciamc.co.uk     -      Copy deadline for Viva Lancia is 12th of each month.      -      For Events e-mail events@lanciamc.co.uk      -      To Join the club go to http://www.lanciamc.co.uk/join.htm
 
   Home   Help Search Calendar Register  
Pages: [1]   Go Down
  Print  
Author Topic: Gear Stick Vibration  (Read 3543 times)
0 Members and 1 Guest are viewing this topic.
Beckerman67
Member
****
Posts: 82



« on: 29 September, 2021, 07:57:15 AM »

 1972 Coupe 1.3s S2

 I'm trying to find the cause of a 'buzzing' noise from the gear stick. It is noticeable in all gears and only lessens if the engine is not under load.
 Travelling on a motorway the noise is very loud and can be stopped by applying pressure on the gear knob or stick.
 My initial thought was to change the bushings which connect the chrome part of the stick to the lower part, however, I've failed in trying to separate
 the two sections as the force required is too much.
 I'm guessing it would be much easier if the complete stick was removed by detaching it from the gearbox linkage which I assume requires access from
 under the car.
 If I manage to change things and the noise is still there, what would be the next step?
 Thanks.
Logged
dhla40
Senior Member
*****
Posts: 188


« Reply #1 on: 29 September, 2021, 10:24:34 AM »

There was a Lancia bulletin about this, if you look under the car the bottom of the gearstick  connects to a rod end which screws into the bottom of the linkage housing.  Remove the bolt and give the rod end a wiggle, if it feels loose unscrew it and you should find a rubber strip in a slot in the thread, turn this around or replace it and wrap some PTFE tape on the thread and screw it back in and refit the gearstick bolt.
If this does not fix the vibration then the shaft bushes or cup bush are probably worn.

Sean
Logged

1976 1.3s coupe
1973 1.3s coupe
1982 montecarlo project
1976 alfa GT
1981 alfa spider
lancialulu
Press Officer
Permanent resident
*****
Posts: 5039



« Reply #2 on: 29 September, 2021, 01:40:13 PM »


If this does not fix the vibration then the shaft bushes or cup bush are probably worn.

Sean

Rod should not wear but bushes do. not an easy job (impossible??) when gearbox is in the car.
Logged

Its not the winning but taking part! or is it taking apart?
Lancias:
1955 Aurelia B12
1967 Fulvia 1.3HFR
1972 Fulvia 1600HF
1972 Fulvia Sport 1600
1983 HPE VX
1988 Delta 1.6GTie
1998 Zeta 21.  12v
davidwheeler
Permanent resident
**
Posts: 1483



« Reply #3 on: 29 September, 2021, 02:12:18 PM »

I think you cannot remove the gear box with the gear stick in situ so yes but you will need to get under.
Logged

David Wheeler.  Lambdas, Aprilia, Fulvia Sport.(formerly Appia and Thema as well).
lancialulu
Press Officer
Permanent resident
*****
Posts: 5039



« Reply #4 on: 29 September, 2021, 02:59:08 PM »

Can I at least get to remove the gear stick with the gearbox in-situ?
And check out the bottom boot.
Logged

Its not the winning but taking part! or is it taking apart?
Lancias:
1955 Aurelia B12
1967 Fulvia 1.3HFR
1972 Fulvia 1600HF
1972 Fulvia Sport 1600
1983 HPE VX
1988 Delta 1.6GTie
1998 Zeta 21.  12v
dhla40
Senior Member
*****
Posts: 188


« Reply #5 on: 29 September, 2021, 04:25:29 PM »

The procedure I described above can be done in situ, prefereably on a ramp, but a jack and a couple of good axle stands will do.

Sean
Logged

1976 1.3s coupe
1973 1.3s coupe
1982 montecarlo project
1976 alfa GT
1981 alfa spider
lancialulu
Press Officer
Permanent resident
*****
Posts: 5039



« Reply #6 on: 11 October, 2021, 03:18:23 PM »

There was a Lancia bulletin about this, if you look under the car the bottom of the gearstick  connects to a rod end which screws into the bottom of the linkage housing.  Remove the bolt and give the rod end a wiggle, if it feels loose unscrew it and you should find a rubber strip in a slot in the thread, turn this around or replace it and wrap some PTFE tape on the thread and screw it back in and refit the gearstick bolt.
If this does not fix the vibration then the shaft bushes or cup bush are probably worn.

Sean

I've removed the gearstick and undone the rod end(12) (which did feel loose), however, there's no rubber strip(32) or slot in the thread? Does the strip fit inside the linkage housing thread? Additionally, would changing the bush(7) be of any benefit?
Never ever had to  change #7.  Also never seen rubber strip. Buzzing down to wear om both #15 bushes and possibly as mentioned before the bottom bolt should be snug so the lever can just operate with out and sticktion..
Logged

Its not the winning but taking part! or is it taking apart?
Lancias:
1955 Aurelia B12
1967 Fulvia 1.3HFR
1972 Fulvia 1600HF
1972 Fulvia Sport 1600
1983 HPE VX
1988 Delta 1.6GTie
1998 Zeta 21.  12v
dhla40
Senior Member
*****
Posts: 188


« Reply #7 on: 11 October, 2021, 05:19:54 PM »

Try wrapping tape around the rod end thread so it is a snug fit.

Sean
Logged

1976 1.3s coupe
1973 1.3s coupe
1982 montecarlo project
1976 alfa GT
1981 alfa spider
Pages: [1]   Go Up
  Print  
 
Jump to:  

Contact the Forum Administrator

LMC Forum copyright © 2007 - 2021 Lancia Motor Club Ltd

Powered by SMF 1.1.20 | SMF © 2006-2011, Simple Machines
Page created in 0.074 seconds with 21 queries.