Lancia Motor Club Forum Banner
13 December, 2024, 07:15:58 PM *
Welcome, Guest. Please login or register.

Login with username, password and session length
News: Need to contact the Forum Administrator? e-mail forum.admin@lanciamc.co.uk     -      Copy deadline for Viva Lancia is 12th of each month.      -      For Events e-mail events@lanciamc.co.uk      -      To Join the club go to http://www.lanciamc.co.uk/join.htm
 
   Home   Help Search Calendar Register  
Pages: [1]   Go Down
  Print  
Author Topic: cooling and heater circuit diagram  (Read 2433 times)
0 Members and 1 Guest are viewing this topic.
dhla40
Senior Member
*****
Posts: 189


« on: 27 July, 2021, 08:17:47 PM »

Does anyone have a diagram of the cooling and heater circuit of a S2? I have a leaking heater matrix and during investigation I noticed that the hose from the top of the engine goes to the valve at the bottom of the heater and the hose from the top of the heater goes to the bottom of the radiator.  I am concerned that this will cause an airlock in the heater during refill, can anyone confirm the correct orientation of the hoses.

Sean
Logged

1976 1.3s coupe
1973 1.3s coupe
1982 montecarlo project
1976 alfa GT
1981 alfa spider
Jaydub
Megaposter
*
Posts: 346


« Reply #1 on: 28 July, 2021, 11:00:23 AM »

Sean, that is correct so that the Hot incoming water from the cylinder head enters the bottom of the matrix and exits from the top thereby pushing any potential air locks out with it and then returns to the inlet of the water pump.
Logged

1600 HF. S2.
nistri
Megaposter
*
Posts: 565


« Reply #2 on: 28 July, 2021, 03:48:00 PM »

plus the fact that, in the engine bay, there should be a tap with a bleed screw in the return hose from the heater to get any air out, rarely necessary if the system is refilled slowly, Andrea
Logged

Andrea Nistri

Ardea S2
Appia S2
Fulvia GTE
Fulvia Sport 1.3 S
Fulvia Montecarlo
Fulvia Coupe 1.3 S
dhla40
Senior Member
*****
Posts: 189


« Reply #3 on: 28 July, 2021, 04:25:23 PM »

OK thanks for confirmation, will take care on refill.

Sean
Logged

1976 1.3s coupe
1973 1.3s coupe
1982 montecarlo project
1976 alfa GT
1981 alfa spider
lancialulu
Press Officer
Permanent resident
*****
Posts: 5058



« Reply #4 on: 28 July, 2021, 04:57:42 PM »

On S2 there was a bleed valve in the return to rad pipe near the engine cross member. I have this on my car. I have never had to use it. The system seems to fill completely without air locks when refilling.

The bleed valve is made from brittle plastic so can break.
Logged

Its not the winning but taking part! or is it taking apart?
Lancias:
1955 Aurelia B12
1967 Fulvia 1.3HFR
1972 Fulvia 1600HF
1972 Fulvia Sport 1600
1983 HPE VX
1988 Delta 1.6GTie
1998 Zeta 21.  12v
Pages: [1]   Go Up
  Print  
 
Jump to:  

Contact the Forum Administrator

LMC Forum copyright © 2007 - 2021 Lancia Motor Club Ltd

Powered by SMF 1.1.20 | SMF © 2006-2011, Simple Machines
Page created in 0.067 seconds with 21 queries.