Lancia Motor Club Forum Banner
04 November, 2024, 06:01:55 AM *
Welcome, Guest. Please login or register.

Login with username, password and session length
News: Need to contact the Forum Administrator? e-mail forum.admin@lanciamc.co.uk     -      Copy deadline for Viva Lancia is 12th of each month.      -      For Events e-mail events@lanciamc.co.uk      -      To Join the club go to http://www.lanciamc.co.uk/join.htm
 
   Home   Help Search Calendar Register  
Pages: [1]   Go Down
  Print  
Author Topic: Engine Install  (Read 4649 times)
0 Members and 1 Guest are viewing this topic.
LCR1967
Member
***
Posts: 34


« on: 07 June, 2021, 07:17:54 PM »

Hi,

I am about to re-install my overhauled engine and looking for some tips on installing from above. I found this thread https://www.lancia.myzen.co.uk/forum/index.php?topic=1184.0 which gave a few tips and on the look out for some more.

I appreciate that most will use the raised body sub-frame method but space is limited so it has ot g oin from above.

Any pointers will be welcome.
Logged
davidwheeler
Permanent resident
**
Posts: 1479



« Reply #1 on: 08 June, 2021, 10:22:13 PM »

It is much easier to take out the subframe, by lifting the body off it, install the engine into that and the lower the car back down onto the assembly.     It does not need significantly more head room than lowering in the engine from the top and saves a great deal of fiddling about.   Also gives you the chance really to check up on the subframe and steering etc.


* DSCF7552 (Copy).jpg (420.94 KB, 1600x1200 - viewed 233 times.)

* DSCF7553 (Copy).jpg (434 KB, 1600x1200 - viewed 241 times.)
« Last Edit: 08 June, 2021, 10:29:01 PM by davidwheeler » Logged

David Wheeler.  Lambdas, Aprilia, Fulvia Sport.(formerly Appia and Thema as well).
LCR1967
Member
***
Posts: 34


« Reply #2 on: 09 June, 2021, 10:07:45 AM »

Thank for the feedback. My space issue is longitudinal.

The space within the sub frame where the engine sits seems tight with the spigot shaft. Any tip on that front? Lossening the GB mounts, raising the GB slightly?
Logged
lancialulu
Press Officer
Permanent resident
*****
Posts: 5031



« Reply #3 on: 09 June, 2021, 03:24:36 PM »

Thank for the feedback. My space issue is longitudinal.

The space within the sub frame where the engine sits seems tight with the spigot shaft. Any tip on that front? Lossening the GB mounts, raising the GB slightly?
It is all a bit of a juggle as you say spigot shaft has to go in to the clutch housing initially at an angle and a trolley jack  under the gearbox (loosening the central mount) can help. I found the fouling was mostly the sump front on the subframe. It generally goes in after a fight if the clutch plate is lined up, and there is no corrosion (rust) on the end of the spigot.
Logged

Its not the winning but taking part! or is it taking apart?
Lancias:
1955 Aurelia B12
1967 Fulvia 1.3HFR
1972 Fulvia 1600HF
1972 Fulvia Sport 1600
1983 HPE VX
1988 Delta 1.6GTie
1998 Zeta 21.  12v
lancianut666
Permanent resident
**
Posts: 1772


Slow but rough


« Reply #4 on: 10 June, 2021, 05:43:17 PM »

Hi
I swapped out a S3 engine to go into my S2 on my ownsome but with a hydraulic engine crane all done from above.
Clarkey
Logged

Fulvia Coupe S2 Flavia Coupe 1967 1.8 Kugelfischer Prisma 1.6 carb Y10 Fila Y10 Touring Dedra 1.8 Dedra 2.0 Turbo Appia S1
davidwheeler
Permanent resident
**
Posts: 1479



« Reply #5 on: 11 June, 2021, 08:16:45 AM »

Basically, there are 6 bolts holding the subframe in.    Then disconnect cables etc, most of them already disconnected and take out the gear stick.  That's it!  Assembly will come out sideways, too.   So much easier!  Good luck whichever way you try.
Logged

David Wheeler.  Lambdas, Aprilia, Fulvia Sport.(formerly Appia and Thema as well).
lancialulu
Press Officer
Permanent resident
*****
Posts: 5031



« Reply #6 on: 11 June, 2021, 01:48:27 PM »

Basically, there are 6 bolts holding the subframe in.    Then disconnect cables etc, most of them already disconnected and take out the gear stick.  That's it!  Assembly will come out sideways, too.   So much easier!  Good luck whichever way you try.
I think you are forgetting the steering box which is a worse pig to put back..... especially with that stupid rubber cover over the splined joint.
Logged

Its not the winning but taking part! or is it taking apart?
Lancias:
1955 Aurelia B12
1967 Fulvia 1.3HFR
1972 Fulvia 1600HF
1972 Fulvia Sport 1600
1983 HPE VX
1988 Delta 1.6GTie
1998 Zeta 21.  12v
Neil
Permanent resident
**
Posts: 1314



« Reply #7 on: 11 June, 2021, 02:34:05 PM »

Try using a few cable ties around the rubber cover to reduce it to a rubber disc, fit the splined shaft to the box, the cut the cable ties off and it covers the joint as normal, it keeps it out of the way
Logged

Neil   
386

1973 Fulvia S2 1.3
LCR1967
Member
***
Posts: 34


« Reply #8 on: 15 June, 2021, 07:32:47 PM »

I installed the engine today from above. Strapped the engine from the intake manifold, loosened all the gearbox bushes, raised the gearbox and pushed it back as far as possible. Pleasantly surprised how easy it went. The fact the engine jack had a load leveller massively simplified the process.

Thank you all for the tips.
Logged
davidwheeler
Permanent resident
**
Posts: 1479



« Reply #9 on: 24 June, 2021, 09:17:32 PM »

Well done!
Logged

David Wheeler.  Lambdas, Aprilia, Fulvia Sport.(formerly Appia and Thema as well).
Pages: [1]   Go Up
  Print  
 
Jump to:  

Contact the Forum Administrator

LMC Forum copyright © 2007 - 2021 Lancia Motor Club Ltd

Powered by SMF 1.1.20 | SMF © 2006-2011, Simple Machines
Page created in 0.048 seconds with 21 queries.