Lancia Motor Club Forum Banner
22 November, 2019, 05:45:59 AM *
Welcome, Guest. Please login or register.

Login with username, password and session length
 
   Home   Help Search Calendar Register  
Pages: [1]   Go Down
  Print  
Author Topic: Aprilia Carburation - Weber 36DCR  (Read 497 times)
0 Members and 1 Guest are viewing this topic.
peterblenk
Member
*
Offline Offline

Posts: 9


« on: 16 September, 2019, 08:18:15 PM »

Does anyone have advice/experience on fitting the Weber 36DCR carburettor to a Series II Aprilia engine? Specifically, what size main and idle jets and which emulsion tube should be used? Should the accelerator pump be used?  I've got the carburettor nicely fitted, and the linkage set up, but the tune is clearly far out. Peter Blenk
Logged
simonandjuliet
Permanent resident
**
Online Online

Posts: 2008



« Reply #1 on: 17 September, 2019, 04:41:44 AM »

Any chance of a photo ? Be good to see the set up.

I will look through various books and see if I have anything
Logged

S1 Aprilia Cabrio, S2 Aprilia, S1 Promiscuo,S2 camioncino, S2 furgoncino, S3 Appia, R4 Sinpar, R4 Rodeo, R60 Tractor, Moto Guzzi Ercole, Disco 3, Mini ALL4 JCW, Moto Guzzi Cardellino 73,Fulvia Berlina GT, Fulvia Rallye S, Fulvia 1600 HF,
Sebastien
Megaposter
*
Offline Offline

Posts: 463


« Reply #2 on: 17 September, 2019, 06:30:04 AM »

Peter,
In 2017 at the spring Lambda meeting at the Phoenix there was a nice black series II Aprilia (at the back of one picture), and I had a good discussion with the owner.
He had a register twin choke Weber fitted (more modern, the one which fitted Cortina GTs in the seventies). For that he had one of the special twin choke manifolds that Gerald Batt had reproduced. The carburettor had been set up and tuned by the following company:
http://www.aireytuning.com/#home
He was very happy about the set up, starting, running, and fuel consumption, and I could see the car was running well.
Hope this helps.


* Aprilia Twin choke - 1.jpg (348.45 KB, 960x1280 - viewed 17 times.)

* Aprilia Twin choke - 2.jpg (330.47 KB, 960x1280 - viewed 18 times.)

* Aprilia Twin choke - 3.jpg (420.95 KB, 1280x960 - viewed 22 times.)
Logged
peterblenk
Member
*
Offline Offline

Posts: 9


« Reply #3 on: 18 September, 2019, 10:27:08 AM »

Thank you, Simon. I am in London, so probably won't make it to Phoenix soon, but I will contact Airey.
Peter
Logged
Andrew White
Member

Offline Offline

Posts: 3


« Reply #4 on: 21 October, 2019, 07:59:07 PM »

Hi Peter, I have recently put an Aprilia back on the road which last ran in 1961 and is fitted with a 36 WEBER.It doesnít run very cleanly yet but I had to solder the float and in doing so altered the float level.I am hoping this explains the poor running! I am about to check it with an air /fuel ratio gauge to see what is happening .If it helps the 3 jets which unscrew vertically are numbered 45,115,60. That is 45 nearest the wing,60 nearest the engine.It has an accelerator pump fitted.Does anyone know what the correct fuel level is? Presumably different density of modern fuel will alter this.The engine is much happier running with a lot more ignition advance than standard. Hope some of this helps !Cheers Andrew White.
Logged
davidwheeler
Permanent resident
**
Offline Offline

Posts: 1079



« Reply #5 on: 25 October, 2019, 11:59:13 AM »

Very many years ago I bought a Weber for an Aprilia from Cavallito and much later sold it to Gerald Batt so if anyone knows the correct setup it is likely to be a Batt.
Logged

David Wheeler.  Lambdas, Aprilia, Fulvia Sport.(formerly Appia and Thema as well).
Kari
Member
***
Offline Offline

Posts: 43


« Reply #6 on: 25 October, 2019, 12:36:04 PM »

Have a look at the table attached. If you need translation, let me know.  Karl


* 100_3195a.jpg (1347.1 KB, 2304x1536 - viewed 30 times.)
Logged
Andrew White
Member

Offline Offline

Posts: 3


« Reply #7 on: 04 November, 2019, 06:28:51 PM »

Hi Peter, Reading my post again ,I see that I put the jets in the wrong order,the main jet is nearest the wing,idle jet in the middle,accelerator pump jet nearest the engine,this is for a 36 5DR.Mine originally had  a 115 main jet which was way too lean,I have progressively drilled this out,and at 135 is now running quite well.It can look lean on initially giving it lots of throttle,but after a second or two the air fuel ratio comes down to safer levels.I may yet go to 140. The idle jet at 45 is fine,more than enough fuel.The accelerator pump for some reason doesnít work,and so far I canít see how to dismantle it,the car drives fine without it.Surprisingly altering the float level didnít seem to alter things as much as expected,and I ended up setting the float horizontal with the arm which bears on the needle vertical.Hope some of this helps.
Logged
Pages: [1]   Go Up
  Print  
 
Jump to:  

Contact the Forum Administrator

LMC Forum copyright © 2007 - 2018 Lancia Motor Club Ltd

Powered by SMF 1.1.20 | SMF © 2006-2011, Simple Machines