Lancia Motor Club Forum Banner
09 December, 2024, 04:55:51 PM *
Welcome, Guest. Please login or register.

Login with username, password and session length
News: Need to contact the Forum Administrator? e-mail forum.admin@lanciamc.co.uk     -      Copy deadline for Viva Lancia is 12th of each month.      -      For Events e-mail events@lanciamc.co.uk      -      To Join the club go to http://www.lanciamc.co.uk/join.htm
 
   Home   Help Search Calendar Register  
Pages: [1]   Go Down
  Print  
Author Topic: Half shafts  (Read 3820 times)
0 Members and 1 Guest are viewing this topic.
baggybird
Member
**
Posts: 10


« on: 18 April, 2019, 11:00:02 AM »

Can anyone advise the best way of removing the old cap and flange on the CV joints.
Hopefully a photo is attached


* B6FAE683-D531-44E4-B403-A4B2ED582454.jpeg (2092.49 KB, 4032x3024 - viewed 459 times.)
Logged
lancialulu
Press Officer
Permanent resident
*****
Posts: 5054



« Reply #1 on: 18 April, 2019, 02:37:27 PM »

Thats a tricky one. I have never had to replace the cv joints on my Fulvias - maybe rebuild them (you can get the 18mm (IIRC) balls at most good bearing outlets)....

If you are determined to swop the sheilds over you could try induction heating the pressing so it expands quicker than the lumps of steel and tapping them off. Use something like Boltbuster with a long LITZ wire wrapped round the diameter. May work may not....
Logged

Its not the winning but taking part! or is it taking apart?
Lancias:
1955 Aurelia B12
1967 Fulvia 1.3HFR
1972 Fulvia 1600HF
1972 Fulvia Sport 1600
1983 HPE VX
1988 Delta 1.6GTie
1998 Zeta 21.  12v
baggybird
Member
**
Posts: 10


« Reply #2 on: 19 April, 2019, 06:29:04 AM »

Got one of the guys in work to chop out these. Worked a treat. If anyone has the same problem I’ll happily post them off.
Turned what I thought would be a weekend of work into a ten minute job.
Now onto the next job.


* 9671C245-12D5-439B-BFEC-F114848A03E7.jpeg (2469.08 KB, 4032x3024 - viewed 451 times.)
Logged
GeoffJohnson
Member
***
Posts: 45


« Reply #3 on: 19 April, 2019, 02:07:41 PM »

If you can find "Wheeler Dealers" Series 15 No 8 on line somewhere you can see Ant Anstead remove these caps when replacing the CV joints.
He put the CV joint in a vice and prised the caps off with a screwdriver.

Geoff Johnson
Logged
peteracs
Administrator
Rebel Poster
*****
Posts: 916



« Reply #4 on: 19 April, 2019, 07:30:42 PM »

Hi

Similar to what I have on the Beta Cv joints and as mentioned above I seem to remember using just a large flat bladed screwdriver and worked round it until it lifted off. Refitting was a similarly simple press on job.

Peter
Logged

Beta Spyder S2 pre F/L 1600
Beta HPE S2 pre F/L 1600
baggybird
Member
**
Posts: 10


« Reply #5 on: 30 April, 2019, 06:36:56 PM »

So half shafts are going back together, a few questions.
Where does washer ‘a’ go?
What is the plastic ring ‘b’ for?
I have the old washer so know it came off but can’t remember where.
I’ve looked in the manual but it doesn’t really show much.
Dry fitting it without the washer the CV joint appears to fit perfectly to allow the circles to fit.
It’s a sloppy fit on the shaft.


* 57E6E9A5-2D8F-4D14-85A8-54B02BC107F8.jpeg (1907.4 KB, 4032x3024 - viewed 518 times.)
Logged
Pages: [1]   Go Up
  Print  
 
Jump to:  

Contact the Forum Administrator

LMC Forum copyright © 2007 - 2021 Lancia Motor Club Ltd

Powered by SMF 1.1.20 | SMF © 2006-2011, Simple Machines
Page created in 0.044 seconds with 21 queries.