Lancia Motor Club Forum Banner
22 November, 2019, 04:38:48 AM *
Welcome, Guest. Please login or register.

Login with username, password and session length
 
   Home   Help Search Calendar Register  
Pages: [1]   Go Down
  Print  
Author Topic: Valve Clearence on the 814.00 engine.  (Read 460 times)
0 Members and 1 Guest are viewing this topic.
Cassino
Member
****
Offline Offline

Posts: 52


« on: 02 March, 2019, 01:20:27 PM »

I have an 814.00 head on my Appia S2 Berlina engine.
Looking at the new APPIA book from Wim......under the chapter:Keep the Appia Fit. the valve clearance and camshaft settings.It says:

For Coupe,convertable/GTE and Sport from engine number 3701 (my engine is 4617)
For these engines with 8 port cylinder head, the procedure is the same as above except that the valve clearance must be set to 1.40mm, The inlet valve just opens at TDC and the exhaust valve 3o before TDC.

Is there anyway I can confirm that what is stamped on the block ,is exactly what it says?
Are there any other "give aways".....to indicate the 814.00 spec. is what I have?

Ian


* empress 406.jpg (4034.9 KB, 3648x2736 - viewed 71 times.)
Logged

Delta Series 3. Appia Berlina Series 2.
Moto BM Zebretta. Moto Guzzi Leggera 65

Previous Lancias.
 Beta Berlina 1400,Delta 1300, Delta GT,Prisma 1500,Prisma 1600 IE, Dedra 1800, Dedra 2000.IESE.
lancialulu
Press Officer
Permanent resident
*****
Offline Offline

Posts: 3606



« Reply #1 on: 02 March, 2019, 02:36:20 PM »

I am not an Appia expert, but this refers to timing the engine rather than valve clearance?
Logged

Its not the winning but taking part! or is it taking apart?
1955 Aurelia B12
1967 Flavia Vignale iniezione
1967 Fulvia HFR
1972 1600 HF
1972 1600 Fulvia Sport
1978 Transformer HF3000 Strato's replica
1979 2500 Gamma Coupe
1988 Delta 1.6GTi.e.
Brian Long
Member
****
Offline Offline

Posts: 66


« Reply #2 on: 03 March, 2019, 09:59:25 AM »

I agree. That figure is for setting the timing, not the clearance for operating purposes.
Lancia uses this engone timing method for most of its motors. I followed this procedure on my B12 and it is 'spot-on'
Logged
lancianut666
Permanent resident
**
Offline Offline

Posts: 1037


Slow but rough


« Reply #3 on: 03 March, 2019, 03:51:30 PM »

Hi
Those figures are for the timing set up see attached PDF taken from the workshop manual there is a difference for this engine for the valve timing
Clarkey

* setting the timing.pdf (793.68 KB - downloaded 44 times.)
Logged

Fulvia Coupe S2 Flavia Coupe 1967 1.8 Kugelfischer Prisma 1.6 carb Y10 Fila Y10 Touring Dedra 1.8 Dedra 2.0 Turbo Appia S1
Cassino
Member
****
Offline Offline

Posts: 52


« Reply #4 on: 14 March, 2019, 01:37:33 PM »

Thanks Clarkey.......printed.


Ian
Logged

Delta Series 3. Appia Berlina Series 2.
Moto BM Zebretta. Moto Guzzi Leggera 65

Previous Lancias.
 Beta Berlina 1400,Delta 1300, Delta GT,Prisma 1500,Prisma 1600 IE, Dedra 1800, Dedra 2000.IESE.
Pages: [1]   Go Up
  Print  
 
Jump to:  

Contact the Forum Administrator

LMC Forum copyright © 2007 - 2018 Lancia Motor Club Ltd

Powered by SMF 1.1.20 | SMF © 2006-2011, Simple Machines