Lancia Motor Club Forum Banner
19 April, 2019, 03:25:46 AM *
Welcome, Guest. Please login or register.

Login with username, password and session length
 
   Home   Help Search Calendar Register  
Pages: [1]   Go Down
  Print  
Author Topic: Loss of reverse gear (B10)  (Read 414 times)
0 Members and 1 Guest are viewing this topic.
brian
Senior Member
*****
Offline Offline

Posts: 171


« on: 11 July, 2018, 09:50:58 AM »

In amidst the misery of the Augusta (to paraphrase Private Eye) see posts passim, was the mention of the loss of reverse gear on the B10 on the way back from SPR.
This morning I have got round to having a look. With not much hope I thought to inspect the gear shift linkage but all the front parts were hidden and looked very complicated so I turned my attention to the rear and it looked ok except very greasy and a bit loose where the M10 bolt goes through the U-shaped end of the long heavy rod from the front.
I cleaned it all off and the rubber of one of the 2 bushes looked tatty and it came away in my hand. Honest Guv, I hardly touched it.
To see if this was the problem I made up a quasi-bush with rolled up gaffer tape , squeezed it in and replaced the bolt.
Eureka! All works normally.
I suppose I ought to get a couple of new bushes (just asked Cavalitto) but I suspect I shall leave as is until it happens again as I will know what the problem is!!
So, my advice is always go for the easiest option as just occasionally it pays off.
Logged

Brian Hands


1922 Hands Tourer
1934 Augusta standard saloon
1938 Aprilia S1 saloon
1953 Aurelia B10
1965 Flavia Sport
williamcorke
Megaposter
*
Offline Offline

Posts: 547


B10


« Reply #1 on: 11 July, 2018, 10:20:38 AM »

That's good news, well done. Not sure I'd trust the duct tape though; couldn't you make a rubber bush from some workshop scrap material?

The front linkage on the bulkhead is indeed quite complicated, but very beautifully made. Your (and my) B10 has a different design at the top to the B21 and B12; typical Lancia. It isn't hard to dismantle or reassemble if the engine is out, but with it in, it's another story.
Logged

'37 Aprilia
'50 B10
'68 Flavia Vignale
'55 Giulietta Sprint
S1 Land Rover
Richard Fridd
Permanent resident
**
Offline Offline

Posts: 2816



« Reply #2 on: 11 July, 2018, 10:24:08 AM »

Good news indeed
Logged

Richard Nevison Fridd
lancialulu
Press Officer
Permanent resident
*****
Offline Offline

Posts: 3463



« Reply #3 on: 11 July, 2018, 11:26:08 AM »

Try Robush if you have the dimensions.
Logged

Its not the winning but taking part! or is it taking apart?
1955 Aurelia B12
1967 Flavia Vignale iniezione
1967 Fulvia HFR
1972 1600 HF
1972 1600 Fulvia Sport
1978 Transformer HF3000 Strato's replica
1979 2500 Gamma Coupe
1988 Delta 1.6GTi.e.
JohnMillham
Rebel Poster
*
Offline Offline

Posts: 904



« Reply #4 on: 11 July, 2018, 01:57:21 PM »

You could try making one out of nylon or similar. It doesn't have to be rubber. When Maltby had the GT Aprilia (NGP50) Bob West and I made brass bushes for the complicated gear linkage, which worked a treat. It was one of the best steering column gear-changes I have ever experienced. Glad it wasn't anything more serious on your B10.
Logged
rogerelias
Rebel Poster
*
Offline Offline

Posts: 923


MY 1600HF IN HEARTBEAT GARAGE


« Reply #5 on: 11 July, 2018, 09:26:46 PM »

I remember going to Ramsgate in NPG 50 as a kid, Maltby lent it to my dad, flippin noisy in the back John
Logged

FULVIA 1600HF LUSSO
1958 VELOCETTE MAC
Triumph Bonneville t120v 1972
1968 MGC ROADSTER
1958 Series 2 Appia berlina
Parisien
Administrator
Permanent resident
*****
Offline Offline

Posts: 3721



« Reply #6 on: 12 July, 2018, 06:33:35 AM »

Good news indeed

Excellent that the fault was easily diagnosed and equally to get sorted.

P
Logged

Frank Gallagher
Pages: [1]   Go Up
  Print  
 
Jump to:  

Contact the Forum Administrator

LMC Forum copyright © 2007 - 2018 Lancia Motor Club Ltd

Powered by SMF 1.1.20 | SMF © 2006-2011, Simple Machines