Lancia Motor Club

Model Technical and Interest => Aprilia, Ardennes and Ardea => Topic started by: josefewald on 26 June, 2017, 06:14:15 PM



Title: engine mount - vibrations
Post by: josefewald on 26 June, 2017, 06:14:15 PM
Hello,

can anybody help me with detailed information regarding the engine mounts?
Instead of the clutch type material I now have softer rubber between the small leaf-springs; the idea was to have a softer bedding of the engine. However, I still have vibrations that are being transferred onto the body by the engine at certain revs.
What is the correct type of material used between the leaf springs?
Any more insider information on the engine mounts?
Many thanks!

Josef


Title: Re: engine mount - vibrations
Post by: GG on 26 June, 2017, 07:20:21 PM
Its very hard to judge what is the original level of vibration, but if its irritating, perhaps look at the details of the installation: look for any direct "metal to metal" contact from the engine side to the body side. Vibration on an Aurelia once took forever to figure out and solve. It was due to the motor mount, compromised and without effective rubber isolation between the engine and the car.


Title: Re: engine mount - vibrations
Post by: ben on 26 June, 2017, 11:34:03 PM
As I understand it the flexibility of the engine mounts arises from the bending of the leaf springs together with the compliance and isolation provided by the rubber spacers above and below the brackets.These rubbers are or should be installed such that there is no metalic contact between the engine brackets and the springs and bolts.
The leaf springs should be clamped together with solid spacers between them,typically made from fibrous material such as clutch lining that you mention. They are there to separate the springs and allow them to flex freely.In practice they slide to and fro a small amount as the springs flex and hence they wear out!
If you have a transmitted vibration problem it might help to install the springs with grease in the interfaces.
I do not think soft spacers between the leaves is a good idea.
If your engine has been rebuilt with replacement pistons or rods etc perhaps you have a fundamental ballance problem?


Title: Re: engine mount - vibrations
Post by: davidwheeler on 27 June, 2017, 02:12:03 PM
I agree, my engine does not vibrate after close attention from Vibration Free after I fitted steel con rods, shell big ends and oversize pistons.  They said that at first "it nearly jumped off the rig".   Aprilia engines should be inherently silky smooth but engine balance in narrow V4s is typically difficult - there is a long essay on the Lamda thread about it (highly complicated mathematics, I warn you).


Title: Re: engine mount - vibrations
Post by: josefewald on 01 July, 2017, 06:39:24 PM
Many thanks to you all for your advice!

I will go back to finding the cause of the vibrations, sort this out (already talked to vibration free) and then check the engine mounting.

Best
Josef


Title: Re: engine mount - vibrations
Post by: ben on 04 July, 2017, 05:38:04 PM
For general interest (!?!?!) I have taken some pictures of the Aprilia engine mount components.
In true Lancia tradition why make a single bonded rubber mount when an arrangement with about 20 individual elements will do!

Hopefully the pictures speak for themselves.
The tubular "bolt" clamps the leaf spring leaves and their spacers together under loading determined by the coil spring to generate friction damping as the leaf springs flex.
The inter leaf spacers are 5mm thick and those above and below the leaves are 3mm thick.
The engine weight (plus any vibration forces) are transmitted through the rubber bushings downwards directly into the leaf spring stack and upwards via the through bolt that goes down through the middle and holds it all together.
When assembling these mounts it is a bit arbitrary how tightly to do up firstly the nut on the hollow bolt clamping the leaves together and then the through bolt which squeezes the rubber bushes as it is tightened.
My recommendation is to compress the coil spring about half way with the tubular bolt.If you overdo it the spring becomes coil-bound and thus serves no purpose and the leaves cannot slide easily as intended.As shown in the last picture I have come across several instances of the hollow bolt having broken away from the upper "u-plate" which acts as the bolt head which is probably because it has been overtightened.
Then when the engine is installed I suggest tightening the through bolts about two turns beyond the point where the clearance is taken up.They then need to be locked with split pins of course!


Title: Re: engine mount - vibrations
Post by: ben on 04 July, 2017, 05:39:58 PM
Ran out of space for this shot!


Title: Re: engine mount - vibrations
Post by: ben on 04 July, 2017, 05:42:04 PM
whoops!


Title: Re: engine mount - vibrations
Post by: GG on 04 July, 2017, 10:17:26 PM
And the technical thinking behind it - here is the patent, which was first filed in 1932, probably for use on the Artena first.


Title: Re: engine mount - vibrations
Post by: simonandjuliet on 05 July, 2017, 05:32:27 AM
Fascinating document !


Title: Re: engine mount - vibrations
Post by: josefewald on 13 September, 2017, 07:35:51 PM
Thanks to everybody for the advice. I think I made quite some progress, although involving some surprise.
I had the engine sent to Vibration free in England, had it balanced and sent back. They told me to look at the thrust washer since it had too much play. Mind you, the engine has run some 5.000 kms. When we had a closer look at this and the crankshaft as well as the bearings we discovered faulty bearings, some white metaling came off the bearings. I had these inspected by a bearing specialist and compared with the original bearings that I kept from the engine overhaul. Unfortunately, the new bearings were faulty since the white material did not stick to its base.
I will now have new bearings made by the white metaling specialist.
I think Aprilia owners should bear in mind that the bearings one can buy today from the main Lancia parts suppliers do not necessarily meet the required standards. This is my experience.
I will write up once we made further progress.
Best regards
Josef


Title: Re: engine mount - vibrations
Post by: ben on 14 September, 2017, 03:25:27 PM
Hi Josef
          Sorry to hear of your continuing problems.
          Hopefully the balancing will still be of some benefit after you have remade the bearings---I assume it is the main bearings that are at fault rather than the big-ends---and you will have to have them line bored again after being re-metalled!!
          Are you able to say who supplied the sub-standard ones?
Ben


Title: Re: engine mount - vibrations
Post by: brian on 14 September, 2017, 07:41:27 PM
As I have said elsewhere, I am a true fan of VibrationFree! They diagnosed a probable main bearing failure and not the propshaft that I suspected and Thornley Kellam are as we speak deciding what path to go down - white metal or shells.


Title: Re: engine mount - vibrations
Post by: davidwheeler on 16 September, 2017, 08:48:30 AM
It is not difficult to modify the big ends to take shells and this would likely give a much longer life.  Mains seem to last a very long time anyway so white metalling would be fine.    Many years ago Harry Manning used to adapt Aprilia crankshafts to take shell bearings by building up the journals but I would think it easier to make carriers to fit in the big end journals to take the shells to substitute for the cariiers that take the white metal- that is unless you have original duraimin rods running directly on the big ends without any other bearing metal!


Title: Re: engine mount - vibrations
Post by: brian on 17 September, 2017, 12:15:06 PM
The only (!) problem with shells is the requirement to put a modern oil filter on instead of the clutch-pedal-operated one.
Brian


Title: Re: engine mount - vibrations
Post by: josefewald on 17 September, 2017, 12:39:12 PM
Hello Ben,
the bearings came from THE source in Torino. Everybody here will know. But this quality problem of reproduced spares keeps chasing me... (now with the Flaminia).
Best
Josef


Title: Re: engine mount - vibrations
Post by: GG on 17 September, 2017, 01:15:59 PM
Don't know about Aprilia, but in the Aurelia, the change to thin shell bearings, and a modern filter also called for changing the oil pump to the later series, higher capacity one. Wasn't a problem, tho.


Title: Re: engine mount - vibrations
Post by: davidwheeler on 17 September, 2017, 04:06:59 PM
www.serdi.co.uk   and http://chaseengineservices.co.uk/ both do white metalling and all Vintage engine work.  I have used both and they both do work of the highest quality.   Serdi have worked on  my Lambda and my Aprilia and Chase on the Lambda.   I don't really see the need to put a modern filter on with shells - difficult in an Aprilia - so long as you change the oil frequently.   I have excellent oil pressure with the standard pump - never out of normale even when hot.   On the other hand, if someone would like to design an adaptor for the Aprilia???  Lambdas have been converted but that is much easier as there is already a nice big filter housing.


Title: Re: engine mount - vibrations
Post by: simonandjuliet on 22 September, 2017, 07:53:00 PM
I've been running the Aprilia on shell bearings since the early 1980's without any problems, the oil pressure is excellent, but with any Aprilia you should change the oil regularly because the filter is not brilliant , shell bearings or no shell bearings